manualshive.com logo in svg

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Поделиться
Скачать
Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 54

52

70410501

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Troubleshooting

36. OM Models: No Display After Selecting One Of The ON/SELECT Keys

120 Volt/60 Hertz/1 Phase CG and CSH Nonreversing; 208-240 Volt/60 Hertz/1 Phase CG and 
CSH Nonreversing; 208-240 Volt/60 Hertz/3 Phase CG and CSH Reversing/Nonreversing; 208-
240 Volt/60 Hertz/3 Phase CE Reversing/Nonreversing; 460-480 Volt/60 Hertz/3 Phase CG, CE 
and CSH Reversing/Nonreversing

OM Models: No display 

after selecting one of the 

ON/ SELECT keys

Is there voltage 

aross the primary of 

the transformer?

TMB2163S

Correct wiring 

between 

transformer and 

supply voltage. 

Check fuses.

Is there 24 VAC 

across terminals 1 & 4 

of transformers 

secondary?

Replace 

transformer.

Is there 24 VAC 

across terminals H3-3 

and H3-4 on the 

micro control?

Correct wiring 

between H3 and 

transformer.  

Check fuses.

Is there voltage 

to the input of the 
fuse on the micro 

control?

Replace 

micro 

control.

Is there voltage 

to the opposite side 

of the fuse on the 

micro control?

Check fuse 

making sure 

it is not blown.  

Replace if 

necessary.

Replace 

micro control.

Yes

No

No

Yes

No

Yes

No

Yes

No

Yes

Содержание ATB50CG






















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды