Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 63

Страница: 63 / 85

70410501

Troubleshooting

42. MM Models: No Heat With Cycle Selected, Unit Running and Calling For

Heat

120 Volt/60 Hertz/1 Phase and 208-240 Volt/60 Hertz/1 Phase Gas and Steam Nonreversing
208-240 Volt/60 Hertz/3 Phase and 480 Volt/60 Hertz/3 Phase Steam Reversing and
Nonreversing

MM Models: No Heat with

cycle selected, unit running

and calling for heat

Is there

voltage to COM

terminal of the
micro control?

TMB2169S-a

Correct wiring

between door

switch and

micro control.

Is there

voltage to the

N.O. terminal

of the micro

control?

Replace

micro control.

Yes

Is there

voltage to the

input of the stove

high limit?

Correct wiring

between stove

high limit and

micro control.

Is there

voltage to the output

of the stove

high limit?

Check for proper

airflow. If airflow is

good, replace stove

high limit.

Is there

voltage to the N.O.

terminal of the

airflow switch?

Correct wiring

between

airflow switch

and stove

high limit.

Is there

voltage at COM

of the airflow

switch?

Check for

proper airflow

and function of

airflow

switch. Replac
e airflow switch

if necessary.

Is there

voltage to the

input of the cabinet

limit?

Correct wiring

to between

cabinet limit

and airflow

switch.

Is there

voltage to the

output of the

cabinet

limit?

Replace

cabinet limit.

Yes

Continued on

Yes

- Gas Models

Yes -
Steam
Models

Содержание ATB50CG






















































































Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды