Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 79

Страница: 79 / 85

70410501

Troubleshooting

51. CD Models: No Heat With Vend Satisfied and Unit Running

120 Volt/60 Hertz/1 Phase and 240 Volt/60 Hertz/1 Phase Gas Nonreversing Models

CD Models: No Heat

with vend satisfied

and unit running

Is there

voltage on red wire

of the motor?

TMB2178S-a

Replace

motor.

there voltage

to the input of

the cabinet

high limit?

Correct wiring

between cabinet

high limit and

motor.

there voltage

to the output of the

cabinet high

limit?

Check for proper

operation.

Replace if

necessary.

there voltage

to the COM terminal

of the airflow

switch?

Correct wiring

between airflow

switch and cabinet

high limit.

there voltage

to the N.O. terminal

of the airflow

switch?

Check for proper

operation and

airflow. Replace

switch if

necessary.

there voltage

to the input side of

the stove high limit

thermostat?

Correct wiring

between stove

limit and airflow

switch.

there voltage

to the output side of

the stove high limit

thermostat?

Check for proper

operation and

airflow. Replace
stove high limit if

necessary.

there voltage

to the N.C. terminal

of switch B on the

coin drop?

Correct wiring

between switch B

and stove high

limit.

Yes

Continued on

Yes

there voltage

to the COM terminal

of switch B?

Check for proper

operation of coin

drop. Replace

switch B if

necessary.

Yes

there voltage

to the input side
of the adjustable

thermostat?

Correct wiring

between

switch B and

thermostat.

Yes

Содержание ATB50CG






















































































Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды