Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 83

Страница: 83 / 85

70410501

Troubleshooting

53. CD Models: No Start With Vend Satisfied and Start Button Pushed

120 Volt/60 Hertz/1 Phase Gas Nonreversing

NOTE: All voltage checks are referenced to neutral unless stated otherwise.

NOTE: If motor only runs with start switch pressed in, that means centrifugal switch in motor is bad.
Replace motor.

CD Models: No start with

vend satisfied and start

button pushed

Is there

voltage to

the N.C. terminal

of switch A?

TMB2180S

Correct wiring

between L1 on

TBI and

switch A.

Unit

operational.

Is there

voltage

to COM terminal

of switch A?

Check for proper

operation of

switch A.

Replace switch A

if necessary.

there voltage

to COM terminal

of the door

switch?

Correct wiring

between door

switch and switch

A of the rotary coin

drop.

With the

door closed, is

there voltage to the

N.O. terminal of the

door switch?

Check door

switch for

proper

operation,

replace if

necessary.

Is there

voltage to

terminal 5 of

the motor?

Correct wiring

between

motor and

door switch.

Is there

voltage to the input

side of the start

switch?

Correct wiring

between start

switch and

door switch.

With the

start button pressed

in, is there voltage to the

output side of the start

button?

Replace start

switch.

Is there

voltage to

terminal 1 of

the motor?

Correct wiring

between

motor and

start switch.

Yes

Does the

motor run?

Replace the

motor.

Yes

Содержание ATB50CG






















































































Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды