York 160.87-OM1 Operation And Maintenance Manual Download

Page: 106 / 268

Variable Speed Drive (VSD) screen

Figure 38: Variable Speed Drive screen

This screen displays information pertaining to a Variable Speed Drive (VSD).

Table 103: Display only

Field/LED name

Description

Motor Run (LED)

Indicates whether the digital output from the controls is

commanding the motor to RUN. Only displayed if this option is

installed.

Motor Heater (LED)

Indicates whether the optional Motor Heater is ON or OFF.

Motor Current % Full Load

Amps

Displays the motor current as a percentage of the Full Load Amps

(FLA) value.

Current Limit Setpoint

Displays the current limit value in use. This value could come from

a 0 to 20mA, 4 to 20mA, 0 to 10VDC or 2 to 10VDC input in Analog

Remote mode, PWM signal in Digital Remote mode, E-Link or SC-

EQ communications interface in ISN mode, or a locally programmed

value.

Pulldown Demand Time Left Displays the time remaining in the programmed pulldown period if

the value is nonzero.

Output Voltage

Displays the output voltage measured to the motor.

Output Frequency

Displays the present output frequency to the motor.

Input Power

Displays the total kilowatts measured by the VSD or Harmonic Filter,

if installed.

YK-EP Style B Centrifugal Chiller

106

Summary of Contents for 160.87-OM1













































































































































































































































































Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands

York 160.87-OM1, Operation And Maintenance Manual

Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands