York 160.87-OM1 Page 118 Operation And Maintenance Manual Download

Page: 118 / 268

Table 117: Programmable

Button

Description

ACC Mapping Enable

Sets the Delta T (Leaving Chilled Liquid Temperature - Setpoint)

needed to be met to enable surge mapping and speed reduction

initially on startup. Programmable over the range of 0.5°F to 20.0°F

(default 1.0°F).

Surge Margin Adjust

This value determines how close the frequency reduction will be

allowed to get to the surge line. Programmable over the range of

0.0 (default) to 25.0 Hz. Service Technicians should refer to

Variable

Speed Drive – Service Instructions (Form 160.00-M4)

prior to adjusting

this setpoint.

Surge Sensitivity

Allows the Service Technician to adjust the sensitivity of the ACC

Surge Detection in the Microboard (surges that occur while the drive

is running at less than maximum frequency). Programmable over

the range of 1.5 to 2.5 with default of 2.0. Smaller values increase

the sensitivity.

Manual Surge Point

Allows the Service Technician to manually log the present running

operating conditions into the surge map as a valid surge point.

When this key is pressed, a dialog box appears requesting a special

password to proceed.

Table 118: Navigation

Button

Access level Description

Home

View

Returns user to HOME Screen.

VSD

View

Returns user to VSD Screen.

Surge Map

Service

Causes a jump to the subscreen that displays the surge map.

YK-EP Style B Centrifugal Chiller

118

Summary of Contents for 160.87-OM1













































































































































































































































































Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands

York 160.87-OM1, Operation And Maintenance Manual

Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands