York 160.87-OM1 Page 16 Operation And Maintenance Manual Download

Page: 16 / 268

OptiView Control Center

Figure 5: OptiView Control Center

The OptiView™ Control Center display is highlighted by a full screen graphics display. This display

is nested within a standard keypad, and is surrounded by SOFT keys which are redefined based

on the currently displayed screen. Eight buttons are available on the right side of the panel, and

are primarily used for navigation between the system screens. At the base of the display are 5

additional buttons. The area to the right of the keypad is used for data entry with a standard

numeric keypad provided for entry of system setpoints and limits.

Table 2: Keypad legend

The DECIMAL key provides accurate entry of

setpoint values.
A ± key has also been provided to allow entry

of negative values and AM/PM selection during

time entry.
In order to accept changes made to the chiller

setpoints, the CHECK key is provided as a

universal ‘Enter’ key or ‘Accept’’ symbol.
In order to reject entry of a setpoint or dismiss

an entry form, the

‘X’

key is provided as a

universal ‘Cancel’ symbol.

Cursor Arrow

keys are provided to allow

movement on screens which contain a large

amount of entry data. In addition, these keys

can be used to scroll through history and event

logs.

YK-EP Style B Centrifugal Chiller

Summary of Contents for 160.87-OM1













































































































































































































































































Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands

York 160.87-OM1, Operation And Maintenance Manual

Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands