York 160.87-OM1 Page 131 Operation And Maintenance Manual Download

Page: 131 / 268

Table 130: Display only

Field/LED name

Description

Pre-Rotation Vanes Position

If equipped with a Pro-rotation Vanes potentiometer, displays the

present Pre-Rotation Vanes position as a value between 0% (closed)

and 100% (full open).

Motor Windings

Temperature

Displays the enabled Motor Winding Temperatures for phase A, B

and C. The setting of the Winding Temperature Protection Setpoint

affects this display as follows: When winding RTD's are enabled,

there are 2 temperatures per phase displayed (otherwise, there

is only 1 per phase). When set to Disabled, no temperatures are

displayed and the heading, text and data boxes do not appear.

Individual temperatures can be disabled using the Temperature

Disable Setpoint (on the MOTOR SETPOINTS Screen). When an

individual temperature is disabled, the temperature data box

does not appear. Any RTD input that registers as an open RTD is

considered invalid and displays as XXX.X.

Average Winding

Temperature

This value is calculated as the average of all enabled and valid Motor

Winding Temperatures. Any winding temperature that registers as

open, out of range or disabled is not used in the calculation. When

RTD's are used for winding temperature measurement, there are a

maximum of 6 temperatures used to calculate the average. When

transmitters are used, there are a maximum of 3 temperatures used

to calculate the average. The text description and data box do not

appear when the Winding Temperature Protection Setpoint is set to

disabled.

Motor Cooling Coil Leak

Detected (LED)

Illuminates when the enabled Motor Cooling Coil Leak Detector

(refer to

Motor Cooling Coil Leak Protection

in Table 131) indicates a

leak. The LED and text description do not appear when the Motor

Cooling Coil Leak Protection Setpoint is set to Disabled.

Motor Bearings

Temperature

Displays the enabled Shaft End and Opposite End motor bearing

temperatures. Any RTD input that registers as an open RTD,

is considered invalid and displays as XXX.X. When the Bearing

Temperature Protection Setpoint is set to Disable, no temperatures

are displayed and the heading, text and data boxes do not appear.

131

YK-EP Style B Centrifugal Chiller

Summary of Contents for 160.87-OM1













































































































































































































































































Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands

York 160.87-OM1, Operation And Maintenance Manual

Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands