York 160.87-OM1 Page 220 Operation And Maintenance Manual Download

Page: 220 / 268

Printing

Figure 69: Printer

Printing overview

A printer can be connected to the Control Center’s Microboard to print the following reports. The

screen from which each report can be generated is listed in parenthesis.

•

Status -

Present system parameters (Printer, Home)

•

Setpoints -

Present programmed values of all setpoints (Printer, Setpoints)

•

Schedule -

Present value of programmed daily schedule (Printer, Schedule)

•

Sales Order -

Information about SALES ORDER Screen (Printer, Sales Order)

•

History -

System parameters at the time of the last normal stop, last fault while running and

last 10 faults, whether running or not (Printer, History)

•

Cycling or Safety Shutdown Initiated Print -

Snapshot of all system parameters at instant

of shutdown. Automatically occurs if printer is connected at time of shutdown.

•

Adaptive Capacity Control (ACC) Surge Map -

System conditions at instant all surge points

were mapped. (Compressor Motor Variable Speed Drive applications; Access Level Required:

SERVICE level) (Printer, ACC)

•

Trend -

Prints a snapshot of the existing TREND Screen data or prints new data collected after

the TREND PRINT key is pressed.

The printer can be permanently connected to the Control Center or connected as required to

produce a report. If permanently connected, a DATA LOGGING feature can produce a status report

automatically, beginning at an Operator selected start time and occurring at an Operator selected

interval thereafter.
The following figures are examples of the different print reports. Solid State Starter application

print reports shown. Electro-Mechanical Starter and Variable Speed Drive reports are similar but

print parameters applicable to those devices.

•

Figure 72: Status

•

Figure 74: Setpoints

•

Figure 76: Schedule

YK-EP Style B Centrifugal Chiller

220

Summary of Contents for 160.87-OM1













































































































































































































































































Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands

York 160.87-OM1, Operation And Maintenance Manual

Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands