York 160.87-OM1 Page 157 Operation And Maintenance Manual Download

Page: 157 / 268

Comms screen

Figure 54: Comms screen

This screen allows definition of the necessary communications parameters. Refer to

Printing

for

details of the printer connections and setup. The COM2 settings are automatically set when the

drive is set to VSD or MVVSD and therefore, the COM2 Setup button will not be displayed.

Table 153: Display only

Field/LED

name

Access level Description

None

–

Table 154: Programmable

Button

Access level Description

Chiller ID

Operator

Displays the numeric chiller ID when used within an ISN network of

chillers. This ID number is also printed at the top of reports.

Printer Setup

and COM2

Setup

Operator

Pressing either key places a green selection box around the first

changeable parameter. Use the ▲ and ▼ keys to place the selection

box around the desired parameter to be changed. With the selection

box around the desired parameter, press the Enter key. A dialog

box is displayed permitting data entry. In VSD or LC-SSS Modbus

Protocol Configuration, COM2 button is not shown because COM2

serial port is used for this interface.

Printer Baud

Rate

–

Displays the baud rate at which the panel communicates with the

printer.

Printer Data

Bits

–

Displays the number of data bits the panel uses to communicate

with the printer.

157

YK-EP Style B Centrifugal Chiller

Summary of Contents for 160.87-OM1













































































































































































































































































Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands

York 160.87-OM1, Operation And Maintenance Manual

Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands