manualshive.com logo in svg

York 160.87-OM1, Operation And Maintenance Manual, Page: 36 / 268

Share
Download
York 160.87-OM1 Operation And Maintenance Manual Download Page 36

Head pressure control screen

Figure 11: Head pressure control screen

This screen displays all parameters related to the Head Pressure Control feature. It also allows for

setting of the setpoints applicable to this feature.
If equipped with this optional feature, it must be enabled on the SETUP Screen. Once enabled, this

screen is accessible from the CONDENSER Screen.
The condenser water flow animation will show flow when the Condenser Liquid Flow Switch senses

flow is present.
A complete explanation of the Head Pressure Control feature are explained in the OptiView Control

Center Service Manual.

Note: 

Requires a login access level of SERVICE.

Table 19: Display only fields

Field/LED name

Description

Entering Condenser Liquid

Temperature

Displays the temperature of the liquid as it enters the standard

condenser tube bundle.

Leaving Condenser Liquid

Temperature

Displays the temperature of the liquid as it leaves the standard

condenser tube bundle.

Head Pressure

Displays the pressure difference between the condenser and

evaporator (condenser minus evaporator).

YK-EP Style B Centrifugal Chiller

36

Summary of Contents for 160.87-OM1













































































































































































































































































Reviews:

No comments