York 160.87-OM1 Operation And Maintenance Manual Download

Page: 89 / 268

Table 77: Adjustable

Field/LED

name

Access level Description

Econ Stop

Refrig Flow

Offset

Service

Range 100 to 5000 CFM, Default 2000 CFM

Displays the difference between the refrigerant flow to start the

economizer and the refrigerant flow to stop the economizer. This

offset prevents the economizer from starting and stopping too

rapidly.

Econ

Temperature

Setpoint

Offset

Service

Range -6.0 to -2.5°F, Default -2.5°F

Displays the economizer temperature setpoint offset.

Econ Startup

Delay

Service

Range 0 to 30 minutes, Default 5 minutes

Displays the amount of time set to delay the start of the

economizer.

Econ Start

Econ Level

Offset

Service

Range 0 to 100%, Default 40%

Shows the position of the Pre-Rotation Vanes at full capacity.

Econ

Level High

Shutdown

Service

Range 80 to 100%, Default 95%

Displays the position of the Pre-Rotation Vanes at full capacity.

Full Capacity

PRV Position Service

Range 80 to 100%, Default 95%

Displays the position of the main compressor PRV when it is

considered to be at Full Capacity.

Econ Exit

Boost Econ

Temp Offset

Service

Range 0 to 5°F, Default 1°F

Displays the offset of the temperature that controls when the chiller

exits the boost mode to go into the economizer mode.

Econ PRV

Start Position Service

Range 0 to 30%, Default 2%

Displays the starting position of the economizer prerotation vanes.

Table 78: Setpoints

Button

Access level Description

Econ Gear

Ratio

Override

Admin

Range 0.0 to 7.0, Default 0.0

Shows the override used if the gears are changed to accommodate

customer performance requirements.

Econ Motor

Slip Factor

Admin

Range 0.98 to 1.0, Default 0

Displays the slip factor of the motor. A 60 Hz motor isn't truly 60 Hz,

but rather a 59% motor. The difference is the slip factor.

Econ

Impeller

Diameter

Override

Admin

Range 0.0 to 1.0, Default 0.0

Displays the change in size of the impeller if a different unit is used

in the economizer.

YK-EP Style B Centrifugal Chiller

Summary of Contents for 160.87-OM1













































































































































































































































































Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands

York 160.87-OM1, Operation And Maintenance Manual

Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands