York 160.87-OM1 Page 116 Operation And Maintenance Manual Download

Page: 116 / 268

Adaptive Capacity Control (ACC) details screen

Modbus protocol configuration

Figure 42: ACC details screen Modbus protocol configuration

This screen displays detailed information pertaining to the Adaptive Capacity Control (ACC). It is

shown above with the OptiView-to-VSD serial communications hardware/interface in the Modbus

Protocol Configuration. In this configuration, the microboard communicates directly with the VSD

Logic Board using Modbus protocol serial communications. The Microboard performs the ACC

function. The Motor Communications Protocol Setpoint (on the SETUP Screen) is set to Modbus in

this configuration. All Medium Voltage Variable Speed Drives (MVVSD) use Modbus protocol.

Note:

Requires a login access level of SERVICE.

Table 116: Display only

Field/LED name

Description

% Full Load Amps

Displays the motor current as a percentage of chiller Full Load Amps

as calculated by the microboard from current values returned from

the drive Logic Board.

Current Limit Setpoint

Displays the current limit setpoint value in use. This value could

come from a 0 to 20mA, 4 to 20mA, 0 to 10VDC or 2 to 10VDC input

in Analog Remote mode, PWM input in Digital Remote mode, E-Link

or SC-EQ communications interface in ISN Remote mode or locally

programmed value in Local mode.

Motor Run (LED)

Illuminated when the Control Center is commanding the drive to

run. Otherwise, it is extinguished.

Output Frequency

Displays the frequency at which the drive is operating the motor.

This value is returned from the drive Logic Board.

YK-EP Style B Centrifugal Chiller

116

Summary of Contents for 160.87-OM1













































































































































































































































































Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands

York 160.87-OM1, Operation And Maintenance Manual

Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands