York 160.87-OM1 Page 29 Operation And Maintenance Manual Download

Page: 29 / 268

Table 10: Display only fields

Field/LED name

Description

Economizer Discharge

Temperature

Displays the temperature of the refrigerant vapor at the discharge

of the Economizer Compressor before the refrigerant enters the

condenser.

Economizer % Full Load

Amps

Displays the percentage of full load amps (FLA) utilized by the

Economizer Motor.

Economizer Current Limit

Displays the Economizer active motor current limit in percentage at

Full Load Amps.

Economizer PRV Position

Displays how open the PRV vanes are in percentage from 100%

(open) to 0% (closed).

Economizer Pressure

Displays the pressure within the Economizer.

Economizer Saturation

Displays the saturation temperature within the Economizer

calculated from the Economizer Pressure.

Economizer Setpoint

Displays the Level setpoint as set in the Economizer screen.

Economizer Level

Displays the refrigerant level in the Economizer.

Oil Sump Temperature

Displays the temperature of the oil in the sump.

Leaving Condenser Liquid

Temperature

Displays the temperature of the liquid as it leaves the condenser

tube bundle.

Entering Condenser Liquid

Temperature

Displays the temperature of the liquid as it enters the condenser.

Condenser Pressure

Displays the pressure of the refrigerant within the condenser.

Condenser Saturation

Temperature

Displays the saturation temperature of the refrigerant within the

Condenser calculated from the Condenser Pressure.

Condenser Drop Leg

Displays the subcooled temperature at the condenser.

Condenser Level

Displays the refrigerant level within the condenser.

Leaving Chilled Liquid

Temperature

Displays the temperature of the liquid as it leaves the condenser

tube bundle.

Entering Chilled Liquid

Temperature

Displays the entering chilled liquid temperature at the evaporator.

Chilled Liquid Setpoint

Displays the Leaving Chilled Liquid Setpoint which is set either

locally on the Setpoint Screen or remotely from a BAS.

Evaporator Pressure

Displays the evaporator pressure.

Evaporator Saturation

Temperature

Shows the saturation temperature of the Evaporator calculated form

the Evaporator Pressure.

Table 11: Programmable

Button

Access level Description

None

–

Table 12: Navigation

Button

Access level Description

Home

View

Returns user to HOME Screen.

System

Service

Returns user to SYSTEM Screen.

YK-EP Style B Centrifugal Chiller

Summary of Contents for 160.87-OM1













































































































































































































































































Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands

York 160.87-OM1, Operation And Maintenance Manual

Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands