manualshive.com logo in svg

York 160.87-OM1, Operation And Maintenance Manual

The York 160.87-OM1 is a versatile and reliable product designed to simplify your maintenance tasks. With its comprehensive Operation and Maintenance Manual, you'll have all the necessary information at your fingertips. Download this user-friendly manual for free at manualshive.com and ensure optimal performance of your product.

Share
Download
background image

Quick start screen

Figure 51: Quick start screen

The Quick Start feature is useful in data center and process control applications where it is

desirable to re-establish cooling as fast as possible after a shutdown or power failure. This feature,

when enabled, allows quicker starts and restarts than normal control. It does this by reducing

the time cycle for chiller restart and once running, loading the chiller as fast as possible. After the

chiller is running and has met a specified setpoint or a specified period of time has elapsed, control

returns to normal.
Quick Start feature has two different start modes:

•

Quick Restart – When the chiller shuts down, if certain conditions are met at the completion

of coastdown (and within 30 seconds thereafter), the VSD is started immediately with no

prelube. The vanes are given a constant open pulse and after the VSD achieves its start

frequency, the speed ramp rate is faster than with normal control.

•

Quick Normal Start – If the conditions for a Quick Restart are not met, the next time the

chiller is started, it has a prelube period just like a normal start, however the vanes will begin

to open at the beginning of prelube, instead of waiting until System Run. At the completion

of prelube, the VSD is started and after the VSD achieves its Start Frequency, the speed ramp

rate is faster than with normal control.

In order to use this feature, the chiller must be equipped with a Variable Speed Drive in Modbus

Protocol Configuration or a Medium Voltage Variable Speed Drive. The low inrush current of a VSD

allows more starts per hour and allows the chiller to start with a more open vane position. It must

be enabled on the Setpoints Screen with an ADMIN password by a qualified Service Technician.

Once enabled, all setpoints and parameters related to this feature are displayed on this screen,

when logged in at SERVICE access level.

149

YK-EP Style B Centrifugal Chiller

Summary of Contents for 160.87-OM1













































































































































































































































































Reviews:

No comments

Related manuals for 160.87-OM1

Yard-Man 21A-448-401 Owner'S Manual preview
21A-448-401
Brand: Yard-Man Pages: 16
York YCAZ33BA3 Manual preview
YCAZ33BA3
Brand: York Pages: 88
Redexim Easy-Core User Manual And Parts List preview
Easy-Core
Brand: Redexim Pages: 14
Garden Gear G2700 Instruction Manual preview
G2700
Brand: Garden Gear Pages: 13
Polar Refrigeration DM075 Instruction Manual preview
DM075
Brand: Polar Refrigeration Pages: 44
Polar Refrigeration GL001 Instruction Manual preview
GL001
Brand: Polar Refrigeration Pages: 48
Weed Eater 168132 Owner'S Manual preview
168132
Brand: Weed Eater Pages: 24
Weed Eater WET6500A Owner'S Manual preview
WET6500A
Brand: Weed Eater Pages: 28
Nemox Freezy 5 Instructions For The Use And Maintenance preview
Freezy 5
Brand: Nemox Pages: 33
Scheppach 5912307901 Translation From The Original Instruction Manual preview
5912307901
Brand: Scheppach Pages: 124
HARRISTON INDUSTRIES 2015 Operator'S Manual preview
2015
Brand: HARRISTON INDUSTRIES Pages: 47
Nakayama MB2000 Owner'S Manual preview
MB2000
Brand: Nakayama Pages: 21
Racing RAC1036ET User Manual preview
RAC1036ET
Brand: Racing Pages: 24
VALERA BF161DF Datasheet preview
BF161DF
Brand: VALERA Pages: 2
EarthWise TC70025 Operator'S Manual preview
TC70025
Brand: EarthWise Pages: 36
York eco YCAS Series Manual preview
eco YCAS Series
Brand: York Pages: 232
Watermark Puretec DF15 User Manual preview
Puretec DF15
Brand: Watermark Pages: 16
Keg King Icemaster G40 Quick Start Manual preview
Icemaster G40
Brand: Keg King Pages: 4

Brands by name

Popular brands

Load more brands