York 160.87-OM1 Page 97 Operation And Maintenance Manual Download

Page: 97 / 268

Table 89: Programmable

Button

Access level Description

Full Load

Amps

Service

Defines the maximum amps at which the motor can operate. This

value is viewable when logged in at OPERATOR or VIEW access level.

Voltage

Range

Service

Allows the user to select specific line voltage range for voltage

checking. When not disabled, this line voltage range is used to

determine a low line and high line voltage threshold for initiating a

shutdown.

Starting

Current

Service

Defines the maximum allowed motor starting amps. The Solid State

Starter will limit the motor Starting Current to this value.

KWH Reset

Admin

Allows the user to reset the cumulative kilowatt hours.

Open SCR

(Enabled/

Disabled)

Service

Allows the user to enable or disable the Solid State Starter Open

SCR safety detection. This must never be disabled unless under

advisement of the Johnson Controls Factory.

Shorted SCR

(Enabled/

Disabled)

Service

Allows the user to enable or disable the Solid State Starter Shorted

SCR safety detection. This must never be disabled unless authorized

by Johnson Controls.

Table 90: Navigation

Button

Access level Description

Home

View

Returns user to HOME Screen.

Motor Details Service

Moves to a subscreen that provides information and setpoints

pertinent to the Motor Monitoring feature if the Motor Monitoring

option is installed.

Motor Lube

View

Moves to the subscreen allowing operator acknowledgement of the

compressor motor lubrication and viewing of the compressor motor

lubrication parameters.

Economizer

Compressor View

Jumps to the Economizer Compressor screen.

YK-EP Style B Centrifugal Chiller

Summary of Contents for 160.87-OM1













































































































































































































































































Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands

York 160.87-OM1, Operation And Maintenance Manual

Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands