York 160.87-OM1 Page 115 Operation And Maintenance Manual Download

Page: 115 / 268

Table 113: Display only

Field/LED

name

Access level Description

Precharge

Relay Output

(LED)

–

Indicates whether the relay controlling the precharge output is

energized.

Trigger SCR

Output (LED)

–

Indicates whether the relay controlling the Trigger SCR Output is

energized.

DC Bus

Voltage

–

Displays the DC Bus voltage as reported by the VSD.

DC Inverter

Link Current

–

Displays the DC Inverter link current as reported by the VSD.

Internal

Ambient

Temperature

–

Displays the ambient temperature inside the VSD cabinet as

reported by the VSD.

Converter

Heatsink

Temperature

–

Displays the heatsink temperature of the converter as reported by

the VSD.

Baseplate

Temperature

–

Displays the baseplate temperature of the 3-phase voltage

regulators as reported by the VSD.

VSD Model

Service

Displays the horsepower configuration of the Variable Speed Drive

control.

100% Full

Load Amps

–

Displays the Full Load Amps value as reported by the VSD.

Table 114: Programmable

Button

Access level Description

Local Motor

Current Limit Operator

Allows the user to specify the maximum allowed motor current (as

a percentage of FLA). When the motor current reaches this value,

the Pre-Rotation Vanes will not be permitted to open further. If the

motor current rises above this value, the Pre-Rotation Vanes will

close to reduce the current to this value.

Pulldown

Demand

Limit

Operator

Allows the user to specify the current limit value (as a percentage

of FLA) to which the chiller will be limited during the specified

pulldown limit time. This value will override the Motor Current

Limit value during this time period. This function is used to provide

energy savings following chiller start-up.

Pulldown

Demand

Time

Operator

Allows the user to set a period of time for which the pulldown

demand limit will be in effect after the chiller starts.

Table 115: Navigation

Button

Access level Description

Home

View

Returns user to HOME Screen.

VSD

View

Returns user to VSD Screen.

115

YK-EP Style B Centrifugal Chiller

Summary of Contents for 160.87-OM1













































































































































































































































































Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands

York 160.87-OM1, Operation And Maintenance Manual

Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands