manualshive.com logo in svg

York 160.87-OM1, Operation And Maintenance Manual, Page: 46 / 268

Share
Download
York 160.87-OM1 Operation And Maintenance Manual Download Page 46

Economizer compressor screen

Figure 14: Economizer compressor screen

This screen displays a cutaway view of the Economizer compressor, revealing the impeller, and

shows all conditions associated with the compressor. In addition, with the proper access level,

the Pre-Rotation Vanes may be manually controlled. Animation of the compressor impeller

indicates whether the chiller is presently in a RUN condition. This screen also serves as a gateway to

subscreens for calibrating the Pre-Rotation Vanes, calibrating the Proximity Probe, configuring the

Hot Gas Bypass, or providing advanced control of the Compressor Motor Variable Speed Drive.

Table 29: Display only

Field/LED

name

Access level Description

Oil Pump

Drive

Command

Frequency

–

Displays the command frequency of the Oil Pump Drive. The

frequency will go up or down to match the pump motor output to

the required oil pressure.

Discharge

Temperature

–

Displays the temperature of the refrigerant in its gaseous state at

discharge of the compressor as it travels to the condenser.

Discharge

Superheat

–

Displays the discharge superheat, calculated as (Discharge

Temperature – Condenser Saturation temperature).

High Speed

Thrust

Bearing Limit

Switch LED

–

Displays when the high-speed thrust bearing limit switch is

activated.

Pre-Rotation

Vanes

Opening LED

–

Displays when the Economizer PRV is opening.

YK-EP Style B Centrifugal Chiller

46

Summary of Contents for 160.87-OM1













































































































































































































































































Reviews:

No comments