York 160.87-OM1 Page 8 Operation And Maintenance Manual Download

Page: 8 / 268

WARNING

External wiring, unless specified as an optional connection in the manufacturer’s product line, is not to

be connected inside the OptiView cabinet. Devices such as relays, switches, transducers and controls

and any external wiring must not be installed inside the micro panel. All wiring must be in accordance

with Johnson Controls’ published specifications and must be performed only by a qualified electrician.

Johnson Controls will NOT be responsible for damage/problems resulting from improper connections

to the controls or application of improper control signals. Failure to follow this warning will void the

manufacturer’s warranty and cause serious damage to property or personal injury.

Changeability of this document

In complying with Johnson Controls’ policy for continuous product improvement, the information

contained in this document is subject to change without notice. Johnson Controls makes

no commitment to update or provide current information automatically to the manual or

product owner. Updated manuals, if applicable, can be obtained by contacting the nearest

Johnson Controls Service office or accessing the Johnson Controls QuickLIT website at

http://

cgproducts.johnsoncontrols.com

It is the responsibility of rigging, lifting, and operating/ service personnel to verify the applicability

of these documents to the equipment. If there is any question regarding the applicability of these

documents, rigging, lifting, and operating/service personnel should verify whether the equipment

has been modified and if current literature is available from the owner of the equipment prior to

performing any work on the chiller.

Revision Notes

Revisions made to this document are indicated in the following table. These revisions are to

technical information, and any other changes in spelling, grammar, or formatting are not included.

Affected pages

Description

Conditioned Based Maintenance program information added

Associated literature

Description

Form number

YK-EP Installation Checklist and Request for Startup Engineer

160.87-CL1

YK-EP Startup Checklist

160.87-CL2

YK-EP Maintenance Log Sheet

160.87-MR1

YK-EP Installation and Reassembly

160.87-N1

YK-EP Operation Manual

160.87-OM1

Wiring Diagram - YK-EP Style B Chillers with OptiView Control Center Water

Pump Starters

160.87-PW1

Wiring Diagram - YK-EP Style B Chillers with OptiView Control Center Field

Control Modifications

160.87-PW2

Wiring Diagram - YK-EP Style B Chillers with OptiView Control Center and

Electro-Mechanical Starter

160.87-PW4

Wiring Diagram - YK-EP Style B Chillers with OptiView Control Center and

Modbus SSS/VSD

160.87-PW5

YK-EP Style B Centrifugal Chiller

Summary of Contents for 160.87-OM1













































































































































































































































































Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands

York 160.87-OM1, Operation And Maintenance Manual

Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands