manualshive.com logo in svg

York 160.87-OM1, Operation And Maintenance Manual

Share
Download
York 160.87-OM1 Operation And Maintenance Manual Download Page 190

System run – Cooling mode

The chiller is running with Heat Pump Duty enabled and the Heat Pump Duty Operational mode

setpoint set to Cooling mode. In this mode, the Heat Pump is controlling the Leaving Chilled Liquid

Temperature to the Leaving Chilled Liquid Temperature Setpoint.

System coastdown

The chiller has shut down and the Post-run lubrication is being performed. The Coastdown

duration is determined by the setting of the Coastdown (standard or enhanced) and Coastdown

Time Setpoints. If the Coastdown setpoint is set to enhanced (steam turbine applications), it

is 15 minutes. If set to standard (electric motor applications), it is programmable over a range

determined by the Chiller Style/Compressor Setpoint (for style G/K6-K7, the range is 240 (default) to

900 seconds.

Start inhibit

The chiller is prevented from being started due to the reason displayed on the Details Line of the

Status Bar.

Vanes closing before shutdown

Displayed while the Pre-Rotation Vanes are closing during a Soft Shutdown. During Soft Shutdowns,

the Vanes are driven fully closed prior to shutting down the compressor. When the Vane Motor End

Switch closes, indicating the Vanes have fully closed (or 3.5 minutes have elapsed, whichever occurs

first), the Run Signal is removed from the compressor motor starter and a System Coastdown is

performed. Soft Shutdowns are initiated by the following:

1.  Leaving Chilled Liquid – Low temperature
2.  Remote Stop
3.  Multi-Unit Cycling – Contacts Open
4.  System Cycling – Contacts Open
5.  Control Panel – Schedule
6.  Operator Initiated at Keypad

While the Vanes are closing during any Soft Shutdown, if a Local Stop is initiated with the

Compressor Switch or any faults other than those listed above occur, the Soft Shutdown is

terminated and it will immediately perform a System Coastdown.

Run messages

Leaving chilled liquid control

The chiller is running, controlling the Leaving Chilled Liquid to the Leaving Chilled Liquid

Temperature Setpoint. There are no system conditions inhibiting this operation.

Heat pump – Leaving chilled liquid control

The Heat Pump is running, controlling the Leaving Chilled Liquid Temperature to the Leaving

Chilled Liquid Temperature Setpoint. In this mode, Heat Pump Duty is enabled and the Heat Pump

Duty Operational mode setpoint is set to Cooling mode.

Current pulldown limit

The Pulldown Demand Limit Setpoint timer is in effect and the Compressor Motor current is

greater than or equal to the Pulldown Demand Current Limit Setpoint value. The Pre-Rotation Vane

operation is being inhibited as described in Motor – High Current Limit message below.

YK-EP Style B Centrifugal Chiller

190

Summary of Contents for 160.87-OM1













































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands