manualshive.com logo in svg

York 160.87-OM1, Operation And Maintenance Manual

The York 160.87-OM1 is a versatile and reliable product designed to simplify your maintenance tasks. With its comprehensive Operation and Maintenance Manual, you'll have all the necessary information at your fingertips. Download this user-friendly manual for free at manualshive.com and ensure optimal performance of your product.

Share
Download
background image

Program Download Connector J26

The SD Program card is inserted into connector J26 to download a program. Refer to instructions

under Service Replacement.

FeRAM

The FeRAM (Ferroelectric Ramdom Access Memory) preserves the stored data during power

failures. All of the programmed Setpoints, Sales Order Data and History Data is stored here. This

memory does not require a battery.

Real Time Clock

The RTC (Real Time Clock) uses a common CR2032 button-cell lithium battery to maintain the time

and date during power outages. The battery life is over 10 years. This type of battery is used in

watches and is readily available at drug stores and appliance stores.

SMARC Module

The SMARC Module is the processor card for the 031-03630-007 microboard. The SMARC Module

and the baseboard are assembled as a pair in the board manufacturing factory and can not be

swapped in the field. SMARC (Smart Mobility ARChitecture) is a relatively new standard to enable

multiple vendors to provide high performance embedded processor cards. This will allow using

future processors if the current ones become obsolete without having to re-design the microboard.

Watchdog Circuit

The Watchdog circuit performs two functions as follows:

•

Power failure detection

•

Program latch-up detection/prevention

The Watchdog Circuit monitors the +5VDC from the power supply and the +3.3VDC from the

onboard regulator to determine when a power failure is occurring. If the +5VDC decreases to

the threshold of (+4.44VDC to +4.68VDC) or the +3.3VDC decreases to the threshold of (+2.84VDC

to +3.04VDC), a reset is issued to the microprocessor and the chiller shuts down. When power is

restored, the white screen is displayed and the boot-up is performed as described above. When the

graphic screen is displayed, the message CONTROL PANEL – POWER FAILURE is displayed.
The Watchdog Circuit also assures that the entire program is being executed and that the program

has not latched-up, bypassing important safety checks. The Watchdog circuit is a timer that times-

out if not given a reset pulse within its time-out period (1 to 1.204 seconds).

YK-EP Style B Centrifugal Chiller

242

Summary of Contents for 160.87-OM1













































































































































































































































































Reviews:

No comments

Related manuals for 160.87-OM1

Carrier 19FA Series Application Data preview
19FA Series
Brand: Carrier Pages: 4
Craftsman 29357 Instruction Manual preview
29357
Brand: Craftsman Pages: 69
Craftsman 536.7975 Owner'S Manual preview
536.7975
Brand: Craftsman Pages: 20
McQuay MicroTech II Operation & Maintenance Manual preview
MicroTech II
Brand: McQuay Pages: 32
Elkay ECP8-2GQ Installation, Care & Use Manual preview
ECP8-2GQ
Brand: Elkay Pages: 2
MTD 219-200 Owner'S Manual preview
219-200
Brand: MTD Pages: 8
MTD 216-310-000 Owner'S Manual preview
216-310-000
Brand: MTD Pages: 21
MTD 214-381-000 Owner'S Manual preview
214-381-000
Brand: MTD Pages: 23
Yard Machines YM121 Operator'S Manual preview
YM121
Brand: Yard Machines Pages: 24
Ozito PTL-4300 Instruction Manual preview
PTL-4300
Brand: Ozito Pages: 10
EarthWise TC70016 Owner'S Manual preview
TC70016
Brand: EarthWise Pages: 36
EarthQuake MC33 Owner'S Manual preview
MC33
Brand: EarthQuake Pages: 24
Parker ICEP002 User Manual preview
ICEP002
Brand: Parker Pages: 56
York YGWH 115 Installation, Commissioning & Operation preview
YGWH 115
Brand: York Pages: 60
aFe Power F-250 Manual preview
F-250
Brand: aFe Power Pages: 13
Weed Eater 173627 Owner'S Manual preview
173627
Brand: Weed Eater Pages: 24
Henny Penny BCF-65 Specification Sheet preview
BCF-65
Brand: Henny Penny Pages: 2
Airwell Itelco-Clima CLC 182 ELN Installation And Maintenance Manual preview
Itelco-Clima CLC 182 ELN
Brand: Airwell Pages: 83

Brands by name

Popular brands

Load more brands