York 160.87-OM1 Page 209 Operation And Maintenance Manual Download | Manualshive

Page: 209 / 268

background image

Table 205: Evaporator pressure thresholds

Shutdown (PSIG)

Restart (PSIG)

Water Cooling - R22

54.3

54.4

- R134a

25.0

25.1

Brine Cooling - R22

25.0 to 54.3 as programmed

+0.1 more than Shutdown threshold

- R134a

6.0 to 25.0 as programmed

+0.1 more than Shutdown threshold

Evaporator – Low Pressure - Smart Freeze

Smart Freeze protection is activated and has shutdown the chiller because the evaporator

temperature has been below the Smart Freeze threshold for greater than the allowable number

of seconds. If the Evaporator Refrigerant Temperature sensor RT7 is enabled, (using procedure

in

OptiView Control Center – Service Instructions (Form 160.54-M1)

), this parameter is used as the

Evaporator Refrigerant Temperature and the freeze threshold is 32.8°F. If RT7 is not enabled, the

Evaporator Refrigerant Temperature used is the Evaporator Saturation Temperature, derived from

the Evaporator Pressure transducer and the freeze threshold is 34.0°F.
The total count is incremented once for every second the Evaporator Refrigerant Temperature is

below the freeze threshold (but is never decremented below zero). The number of seconds it will

take the chilled liquid to freeze is based on how far the Evaporator Refrigerant Temperature is

below the freeze threshold as follows:

number of seconds

to freezing

=

(4053.7)

freeze threshold -

evap. refrigerant temp.

Smart Freeze is activated only if the feature has been enabled by a Service Technician (following

instructions in

OptiView Control Center – Service Instructions (Form 160.54-M1)

) and the Leaving

Chilled Liquid Temperature Setpoint is less than 38.0°F.

Evaporator – Transducer Or Leaving Liquid Probe

A possible defective Evaporator Pressure transducer or Leaving Chilled Liquid temperature

transmitter has been detected. The pressure and temperature that these devices are indicating

are not in the correct relationship to each other. The Control Center converts the Evaporator

Pressure to a Saturated Temperature value and compares this value to the Leaving Chilled Liquid

temperature (difference equals chilled liquid temp minus evaporator saturated temp). The

difference should not be outside the range of –2.5°F to +25.0°F. If the transducer and transmitter

are accurate, the Evaporator Saturated temperature should not be greater than 2.5°F warmer

nor greater than 25.0°F colder than the Leaving Chilled Liquid Temperature. In order to initiate a

shutdown, the difference must be outside the acceptable range continuously for 10 minutes. The

chiller can be started after the Operator presses the WARNING RESET button.

Evaporator – Transducer Or Temperature Sensor

A possible defective Evaporator Pressure transducer or Refrigerant Temperature Sensor has

been detected. The Control Center converts the Evaporator Pressure to a Saturated Temperature

value and compares this value to the optional Evaporator Refrigerant Temperature Sensor. If

the difference between these temperatures is greater than 3.0°F, continuously for 1 minute, this

shutdown is performed. This check is only performed under the following conditions:

•

Chiller has been running for at least 10 minutes

209

YK-EP Style B Centrifugal Chiller

«
...
207
208
209
210
211
...
»

Summary of Contents for 160.87-OM1













































































































































































































































































Reviews:

No comments

Related manuals for 160.87-OM1

Brand: ACS Pages: 83

Brand: AGRI EASE Pages: 46

LSBLG MCF Series

Brand: Midea Pages: 116

Brand: Zanussi Pages: 3

Brand: Zanussi Pages: 3

Brand: Zanussi Pages: 4

Brand: Cub Cadet Pages: 24

Brand: Cub Cadet Pages: 23

Brand: Carrier-Sanyo Pages: 46

Brand: Häfele Pages: 11

Brand: Gardol Pages: 148

A540 DiXL V-2203

Brand: Jensen Pages: 110

Brand: Haier Pages: 37

Brand: Samsung Pages: 52

Brand: EarthQuake Pages: 24

Brand: EarthQuake Pages: 28

Brand: EarthQuake Pages: 28

Brand: EarthQuake Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands