York 160.87-OM1 Page 65 Operation And Maintenance Manual Download

Page: 65 / 268

Table 50: Display only

Field/LED name

Description

ACC Surge Detected (LED)

Only displayed if equipped with a VSD or MVVSD. Illuminates

momentarily when a surge is detected by the ACC function in

the Microboard, while the drive is running at less than maximum

frequency.

VGD Count

Displays the number of times the Stall Detector Board output

voltage goes above the High Limit Setpoint. The count can be

cleared with an ADMIN access level using the VGD CYCLE COUNT

key on the VGD SETPOINTS Screen.

VGD Time ( __Days __Hrs

__Min __Sec)

Displays the accumulated time the Stall Detector Board output

voltage is greater than the High Limit Setpoint while the chiller is

running.

Control Status

Displays the current state of the VGD control. The states are: Stall

Waiting, Stall Reacting, Probing, Surge Reacting, Surge Waiting, Hot

Gas Override.

Time Remaining

While the VGD is in the Stall Waiting State, displays the time

remaining in the Probe Wait Time interval (value programmed as

the Probe Wait Time setpoint).

Diffuser Gap Control Mode Indicates whether the VGD is under manual or automatic control.

Table 51: Programmable

Button

Access level Description

[VGD] Open

(Manual)

Service

This key puts the VGD in manual mode and sends an OPEN

command to the VGD

[VGD] Close

(Manual)

Service

This key puts the VGD in manual mode and sends a CLOSE

command to the VGD.

[VGD] Hold

(Manual)

Service

This key puts the VGD in manual mode and sends a HOLD command

to the VGD.

Table 52: Navigation

Button

Access Level Description

Home

View

Returns user to HOME Screen.

Compressor View

Returns user to COMPRESSOR Screen.

VGD

Setpoints

Service

Move to the subscreen that allows programming of the Variable

Geometry Diffuser setpoints

YK-EP Style B Centrifugal Chiller

Summary of Contents for 160.87-OM1













































































































































































































































































Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands

York 160.87-OM1, Operation And Maintenance Manual

Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands