York 160.87-OM1 Page 24 Operation And Maintenance Manual Download

Page: 24 / 268

Table 5: Programmable

Button

Access level Description

Clear Fault

Service

When any safety conditions have been detected and the chiller has

been shutdown, the main status display of the chiller will continue

to display a message indicating the cause of the shutdown. Using

this key, the message can be cleared once the Safety condition has

been removed.

Warning

Reset

Operator

Use of this key acknowledges a warning condition and resets the

message display associated with it.

Start/Stop

Soft Key

Operator

This key will initially be displayed as Start and when pressed, allows

the operator to Start the chiller. If the chiller is in Local mode it

will start immediately. If the chiller is in Remote mode then it will

start once the Start key is pressed and the remote mode calls for

a start. Once started, the soft key changes to Stop and if pressed,

will initiate a Soft Stop. A Soft Stop fully closes the Pre-Rotation

Vanes prior to shutting down the compressor. This reduces bearing

wear by eliminating compressor backspin at shutdown. While the

vanes are closing, "Vanes Closing Before Shutdown" is displayed

on the System Status Line. When the Vane Motor Switch (VMS)

closes, indicating the vanes have fully closed (or 3.5 minutes

have elapsed, whichever occurs first), the Run signal is removed

from the compressor motor starter and a System Coastdown is

performed. While the vanes are closing, if a Safety Stop is initiated

with the Safety Stop Switch or any fault other than Leaving Chilled

Liquid Temp – Low Temperature, Remote Stop, Multi-Unit Cycling –

Contacts Open, System Cycling – Contacts Open Or Control Panel –

Schedule occur, it will immediately enter System Coastdown.

Table 6: Navigation

Button

Description

System

Used to provide additional system information.

Evaporator

A detailed view of all evaporator parameters, including the programmable

Leaving Chilled Liquid Setpoints.

Condenser

A detailed view of all condenser parameters, including control of the liquid

level functions.

Compressor

A detailed view of all the compressor parameters. This includes Pre-Rotation

Vane control, Hot Gas Bypass Control, Proximity Probe Calibration, and PRV

Calibration.

Oil Sump

A detailed view of all the oil pump and oil sump parameters. This includes the

Variable Speed Oil Pump when installed. It also controls the Seal Lubrication

functionality.

YK-EP Style B Centrifugal Chiller

Summary of Contents for 160.87-OM1













































































































































































































































































Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands

York 160.87-OM1, Operation And Maintenance Manual

Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands