York 160.87-OM1 Operation And Maintenance Manual Download

Page: 240 / 268

Table 209: Test points and LED indicators

Voltage

Test point

Voltage range

Fuse

LED

+5VDC

TP3

+4.92 to +5.28VDC

F1 (5A)

CR56

+12VDC

TP4

+11.58 to +12.5VDC

F2 (5A)

CR57

-12VDC

TP33

-11.5 to -12.5VDC

F3 (5A)

CR58

+24VDC

TP35

+22.4 to +26.7VDC

F4 (4A)

CR59

+3.3VDC

TP2

+3.25 to +3.43VDC

n/a

CR62

VCC

TP15

+4.92 to +5.28VDC

n/a

+5VA

TP10

+4.95 to +5.05

n/a

CR61

Battery

n/a

+2.95 to +3.45

n/a

Boot-up program

The Boot-up Program is stored in Flash memory. It may be updated along with a new version of the

operating program by inserting an SD card containing the new program into the SD card slot on the

03630 board, setting DIP Switch SW1 position 4 to ON and then applying power to the chiller. The

Boot-up Program version is displayed on the DIAGNOSTICS Screen in SERVICE access level.

Table 210: Diagnostic display codes

LED display code

(normal boot up)

Description

DIP 4 OFF - Booting from internal Flash program

Flash Checksum Test in progress

Application program setup in progress

∞

Application program is running

LED display code (other)

DIP 4 ON - Booting from SD card [Normal when loading a

program]

DIP 4 ON - Booting from USB port

DIP 4 ON - PIC application is being configured

DIP 4 OFF - Boot from internal Flash Failed [Try to reload the

program]

DIP 4 ON - Boot from SD card Failed [Bad SD card or Bad

microboard]

DIP 4 ON - Microboard Internal error [Bad microboard]

DIP 4 ON - Checksum Failed [Try to reload program, Bad

microboard]

DIP 4 ON - Boot from SD card Failed

Note:

If the display stops at a 01 display, this may be an indication that the SD card reader is

defective.
If the display stops at the YORK logo with a white screen, this indicates that the board has no

program to boot from.

YK-EP Style B Centrifugal Chiller

240

Summary of Contents for 160.87-OM1













































































































































































































































































Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands

York 160.87-OM1, Operation And Maintenance Manual

Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands