York 160.87-OM1 Page 85 Operation And Maintenance Manual Download

Page: 85 / 268

Economizer capacity control screen

Figure 29: Economizer capacity control screen

This screen displays a view of the economizer capacity control setpoints and buttons. It provides all

necessary inputs for manual control of the economizer.

Table 74: Display only

Field/LED name

Description

Economizing Mode LED

LED lights up when the economizer or the Anti Surge is operating.

Economizer Saturated

Temperature

Displays the saturation temperature within the economizer.

Anti Surge Minimum

Temperature

Displays the minimum temperature that the economizer can go to

before the economizer compressor will start to surge. Efficiency of

the economizer will be the highest at this point.

Delta T

Displays the temperature that is the result of subtracting the

Economizer Saturation Temperature minus the Economizer

Saturation Temperature Setpoint.

Motor Current % FLA

Displays the percent of full load amps of the economizer

compressor motor.

Override Threshold

If Motor Current % full load amps is higher than the Override

Threshold, the capacity control will be overridden, it means the

economizer prerotation vanes can't be opened more to increase the

capacity.

Boost Mode LED

This LED is on whenever the Economizer Operation Mode is Boost or

Boost Anti Surge.

Entering Chilled Liquid

Temperature

Displays the entering chilled liquid temperature at the evaporator

and the condenser.

YK-EP Style B Centrifugal Chiller

Summary of Contents for 160.87-OM1













































































































































































































































































Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands

York 160.87-OM1, Operation And Maintenance Manual

Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands