York 160.87-OM1 Page 58 Operation And Maintenance Manual Download

Page: 58 / 268

Table 43: Display only

Field/LED name

Description

Surge Avoidance Surge

Count

This is the total number of surges accumulated by the Surge

Protection feature. If equipped with a VSD or MVVSD, it is only the

surges detected while the drive is running at maximum frequency.

Surge Avoidance Surge

Detected (LED)

Illuminates momentarily when a surge is detected by the Surge

Protection feature. If equipped with a VSD or MVVSD these are

only the surges detected while the drive is running at maximum

frequency.

It illuminates momentarily when a surge is detected by the Surge

Protection feature. If equipped with a VSD, it illuminates whenever a

surge is detected, regardless of the VSD operating speed.

Hot Gas Bypass Control

Mode

Indicates whether the Hot Gas Bypass is under automatic, manual

or override control. When in manual control, it is controlled from

this screen. When in override control, Minimum Load, VSD Override

or VGD Override is displayed as appropriate. Refer to the OptiView

Control Center Service Manual for details of these messages.

Table 44: Valve position

Actual position

Valve position %

0% to 19%

0% (fully closed)

20% to 39%

25% open

40% to 59%

50% open

60% to 79%

75% open

greater than 79%

100% (fully open)

Table 45: Programmable

Button

Access level Description

Percentage

Service

(5 to 15% Default 15%)

This is the incremental amount that the Hot Gas Valve will be closed

at 10 minute intervals after the HOLD period has elapsed.

Hold Period

Service

(30 to 120 minutes; default 30 minutes)

This is the period of time after no more surges are detected that the

Hot Gas Valve closing will begin.

Minimum

Load

Service

(0 to 4°F; default 0°F)

This sets the offset below the Leaving Chilled Liquid Temperature

Setpoint at which the Hot Gas Valve will be opened to the position

allowed by the Maximum Open Setpoint.

Maximum

Open

–

(25 to 100%)

The maximum allowable position for the Hot Gas Valve during a

Minimum load override condition.

YK-EP Style B Centrifugal Chiller

Summary of Contents for 160.87-OM1













































































































































































































































































Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands

York 160.87-OM1, Operation And Maintenance Manual

Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands