York 160.87-OM1 Page 95 Operation And Maintenance Manual Download

Page: 95 / 268

Table 86: Programmable

Button

Access level Description

–

Pressing this button will set the Condenser Level Control Valve

Mode to Manual, if it had been in Auto and will decrease the current

Condenser Level Control Valve Command by an amount equal to the

Manual Increment, with a minimum limit of 0.0%.

Set

Service

Pressing this button will open a dialog box where the user can

manually enter a valve command. Once a legitimate value has been

entered and the Enter key pressed, the Condenser Level Control

Valve Mode will be set to Manual, if it had been in Auto and the

Condenser Level Control Valve Command will be set to the entered

value.

Auto

Service

This button is only displayed when in Manual Level Control. Pressing

this button returns the control to the PID program.

Change

Setpoints

–

This button is only displayed when signed in at Service Level.

Pressing this button allows the user to select any of the setpoint

parameters using the arrow keys.

Table 87: Navigation

Button

Access level Description

Home

View

Returns user to HOME Screen.

Condenser

Service

Returns the user to the CONDENSER screen.

YK-EP Style B Centrifugal Chiller

Summary of Contents for 160.87-OM1













































































































































































































































































Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands

York 160.87-OM1, Operation And Maintenance Manual

Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands