York 160.87-OM1 Page 255 Operation And Maintenance Manual Download | Manualshive

Page: 255 / 268

background image

This setpoint is set at the factory at time of manufacture and requires an ADMIN password to

change it. It is only visible when set to Extended. The selections are:

1.

Standard

– Uses standard high pressure warning and safety shutdown thresholds as follows:

- Warning – High Pressure Limit – Maximum allowable value is 162.5 PSIG
- Condenser – High Pressure – Trip/reset threshold is 180/120 PSIG
- Condenser – High Pressure – Stopped – Trip/reset threshold 160 PSIG.

2.

Extended

– Uses higher high pressure warning and safety shutdown thresholds as follows:

- Warning – High Pressure Limit – Maximum allowable value is 193.0 PSIG
- Condenser – High Pressure – Trip/reset threshold is 200/140 PSIG
- Condenser – High Pressure – Stopped – Trip/reset threshold is 170 PSIG

PRV Position

New production chillers can be equipped with an optional Pre-rotation Vanes

potentiometer, regardless of other options. This setpoint allows the software to be used in all YK-

EP chillers, whether equipped with the potentiometer or not. The PRV position will be shown on

respective screens when Enabled; not shown when Disabled.

1.

Enabled

– Automatically set to this setting if Hot gas bypass or Variable Geometry Diffuser

(VGD) is enabled on the OPERATIONS Screen or Motor Drive Type setpoint is set to VSD or

MVVSD. The actual connection point of the potentiometer is determined by the equipment

conﬁguration:

- If equipped with a VSD in YORK Protocol configuration, it is connected to the ACC

Board.

- In Modbus Protocol configuration, it is connected to the microboard J7.

If not equipped with a VSD, but equipped with Hot gas bypass, the connection

point is determined by which I/O Board is present. With I/O Board 371-02514-000

or 031-02895-000, it is connected to this board; otherwise, it is connected to the

microboard J7. If not equipped with Hot gas bypass but equipped with a VGD, it is

connected to the microboard J7.

2.

Disabled

– Set to this position when not equipped with a PRV potentiometer. If equipped with

a VSD, MVVSD or the Hot gas bypass or Variable Geometry Diffuser is enabled, this setpoint is

automatically enabled and cannot be set to disabled.

- Motor Monitoring

The Motor Monitoring feature to be enabled or disabled. Motor Monitoring can not be

used with the 371-02514-000 since the Motor Monitoring and the Frick Analog board

use different protocols.

- Heat Recovery

Allows the Heat Recovery feature to be enabled or disabled.

- Head Pressure Control

Allows the Head Pressure feature to be enabled or disabled.

255

YK-EP Style B Centrifugal Chiller

«
...
253
254
255
256
257
...
»

Summary of Contents for 160.87-OM1













































































































































































































































































Reviews:

No comments

Related manuals for 160.87-OM1

Brand: EarthQuake Pages: 36

Brand: Daikin Pages: 34

Brand: FHM Pages: 38

FTS FLEXICOOL IMMERSION COOLERS FC100

Brand: SP Scientific Pages: 38

Brand: Nordcap Pages: 12

YCAL0043E Series

Brand: York Pages: 184

Brand: Cadet Pages: 20

Brand: Honda Pages: 64

Brand: Honda Pages: 60

Brand: Honda Pages: 60

Brand: Honda Pages: 270

HRS030-A-20 series

Brand: SMC Corporation Pages: 160

Brand: Weed Eater Pages: 28

Brand: Craftsman Pages: 52

Brand: Craftsman Pages: 56

Brand: Wallenstein Pages: 44

Brand: Wallenstein Pages: 72

Brand: F.F. Group Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands