manualshive.com logo in svg

York 160.87-OM1, Operation And Maintenance Manual, Page: 124 / 268

Share
Download
York 160.87-OM1 Operation And Maintenance Manual Download Page 124

Table 124: Display only

Field/LED

name

Access level Description

DC Bus

Voltage

–

Displays the DC Bus voltage as measured by the Harmonic Filter.

Supply

Contactor

(LED)

–

Indicates whether the output to the Supply Contactor is energized.

Precharge

Contactor

(LED)

–

Indicates whether the output to the Precharge Contactor is

energized.

Phase

Rotation

–

Displays the phase rotation detected by the Harmonic Filter (A, B, C

or C, B, A)

Total Supply

kVA

–

Displays the total supply Kilovolt-Amps measured by the Harmonic

Filter.

Heatsink

Temperature

–

(Labeled Baseplate Temperatures on VSD with part number

371-03789-xxx (503HP 60Hz; 419HP 50Hz). Displays the temperature

of the Harmonic Heatsink (baseplate).

Voltage Peak

(N-L1, N-L2,

N-L3)

–

Displays the 3-phase peak voltages as measured by the Harmonic

Filter (Neutral to Line).

RMS Voltage

(L1-L2, L2-L3,

L3-L1)

–

Displays the 3-phase RMS Voltages across each line.

Voltage Total

Harmonic

Distortion

(L1, L2, L3)

–

Displays the 3-phase voltage Total Harmonic Distortion (THD)

measurements.

RMS Filter

Current (L1,

L2, L3)

–

Displays the 3-phase filter current values as measured by the

Harmonic Filter.

Supply

Current Total

Demand

Distortion

(L1, L2, L3)

–

Displays the 3-phase Current Total Demand Distortion (TDD)

measurements.

RMS Supply

Current (L1,

L2, L3)

–

Displays the 3-phase RMS Voltages across each line.

YK-EP Style B Centrifugal Chiller

124

Summary of Contents for 160.87-OM1













































































































































































































































































Reviews:

No comments