York 160.87-OM1 Page 52 Operation And Maintenance Manual Download

Page: 52 / 268

Table 34: Display

Field/LED name

Description

Vane Motor Switch

Displays the state of the Vane Motor Switch as being either open or

closed.

PRV Position

Displays the position of the Pre-Rotation Vanes in percent over the

range of 0% (full close) to 100% (full open).

% Full Load Amps

Displays the full load amps of the economizer compressor motor in

percentage.

Calibration in Progress

(LED)

Indicates the calibration sequence is in progress.

Note:

For fields requiring access level of SERVICE. Qualified service technicians should refer to

the OptiView Control Center Service for operation instructions and explanations of all

programmable setpoints and displayed values.

Table 35: Programmable

Button

Description

PRV Actuator Mode

Displays the Pre-Rotation Vanes actuator mode as Manual or

Automatic.

Open

Pressing this button will open the Pre-Rotation Vanes.

Pressing this button will close the Pre-Rotation Vanes.

Hold

Pressing this button will hold the Pre-Rotation Vanes in a set

position.

Auto

Pressing this button will set the economizer Pre-Rotation Vane

actuator command to Auto. This button will be enabled only when

the Economizer PRV Actuator Mode is not Manual.

Start Calibration

Pressing this button begins the calibration process. When the

Start button is pressed, it will change to a Stop Calibration button.

Pressing the Stop Calibration button will stop the calibration process

and change the button back to the Start Calibration button

Table 36: Navigation

Button

Access level

required

Description

Home

View

Returns user to HOME Screen.

Economizer

Compressor View

Returns user to ECONOMIZER COMPRESSOR screen

YK-EP Style B Centrifugal Chiller

Summary of Contents for 160.87-OM1













































































































































































































































































Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands

York 160.87-OM1, Operation And Maintenance Manual

Search results

Summary of Contents for 160.87-OM1

Reviews:

Related manuals for 160.87-OM1

Brands by name

Popular brands