York 160.87-OM1 Page 60 Operation And Maintenance Manual Download | Manualshive

Page: 60 / 268

background image

Surge protection screen

Figure 20: Surge protection screen

This screen displays a cutaway view of the chiller compressor and all parameters relating to the

Surge Protection feature. All setpoints relating to this screen are maintained on this screen.
The Surge Protection feature detects surge events and provides a running count of the surges

detected over the lifetime of the chiller. It allows the user to define how many surges are excessive

and how the control will react to an excess surge condition. When excess surging is detected, it

can be configured to shutdown the chiller, or initiate a surge avoidance mode while allowing it to

continue to run or simply display a warning message. The sensitivity of this surge detection is set

by the Sensitivity Setpoint on this screen. The surges detected by this feature are also used for the

Hot Gas Bypass feature (Refer to

Hot gas bypass screen

).

The detection and counting of surges in this feature is completely independent of the surge

detection/counting performed by the Variable Speed Drive (VSD) Adaptive Capacity Control (ACC)

Surge Detection. The ACC Surge Detection creates a surge map used to control the speed of the

drive. The ACC Surge Detection is performed in the Microboard

Table 47: Display only

Field/LED name

Description

Delta P/P

A parameter that represents the system differential or Head

Pressure. It is calculated as (condenser pressure – evaporator

pressure) / evaporator pressure.

Surge Avoidance Surge

Detected (LED)

Illuminates momentarily when a surge is detected by the Surge

Protection feature. If equipped with a VSD or MVVSD these are

only the surges detected while the drive is running at maximum

frequency.

Surge Avoidance Surge

Count

This is the total number of surges accumulated by the Surge

Protection feature. If equipped with a VSD or MVVSD, it is only the

surges detected while the drive is running at maximum frequency.

YK-EP Style B Centrifugal Chiller

60

«
...
58
59
60
61
62
...
»

Summary of Contents for 160.87-OM1













































































































































































































































































Reviews:

No comments

Related manuals for 160.87-OM1

Brand: EINHELL Pages: 88

Brand: Huskee Pages: 36

Brand: McQuay Pages: 53

Brand: PrimAster Pages: 32

Brand: Cobra Pages: 16

Brand: Cobra Pages: 11

Brand: MTD Pages: 2

Brand: MTD Pages: 3

Brand: Fort Pages: 36

Brand: Häfele Pages: 11

Brand: Wallenstein Pages: 44

Brand: lancer Pages: 28

Koolant Koolers N-Series

Brand: Hypertherm Pages: 77

Brand: York Pages: 168

quickchiller QC-3

Brand: Alto-Shaam Pages: 2

Lancer P400T V2

Brand: Hoshizaki Pages: 17

Brand: EINHELL Pages: 255

Brand: Makombi Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands