YASKAWA
TOMPYEULA7002A LA700 Series Installation and Operation Instruction
27
b.
If you do not know the mechanical data, for example, in modernization case, you can use the speed ratio
to determine the mechanics:
i.
Set the speed of the elevator car to
o1-18 [Speed of Elevator Car]
.
ii.
Set the elevator motor speed to
o1-19 [Elevator Motor Speed]
.
Note:
When you use the speed ratio, the drive ignores the dedicated mechanical parameters (
o1-2x
)
Refer to
for more information.
■
Drive Parameters
Refer to the following table to set the most important parameters.
Note:
•
You can change parameters that have
“
RUN
”
in the
“
No.
”
column during drive operation.
•
Parameters that have
“
Expert
”
in the
“
No.
”
column are available in Expert Mode only. Set
A1-01 = 3 [Access Level Selection = Expert
Level]
to show and set Expert Mode parameters on the keypad.
No.
Name
Description
A1-00
RUN
Language Selection
Sets the language for the LCD keypad.
0: English, 1: Japanese, 2: German, 3: French, 4: Italian, 5: Spanish, 6: Portuguese, 7: Chinese, 8: Czech, 9: Russian,
10: Turkish, 11: Polish, 12: Greek
A1-02
Control Method Selection
Sets the control method for the drive application and the motor.
0: V/f Control, 2: Open Loop Vector, 3: Closed Loop Vector, 7: PM Closed Loop Vector
A1-03
Initialize Parameters
Sets parameters to default values.
0: No Initialization, 1110: User Initialization, 2220: 2-Wire Initialization
b1-01
Speed Reference Selection 1
Sets the input method for the speed reference.
0: Keypad, 1: Analog Input, 2: Memobus/Modbus Communications, 3: Option PCB
b1-02
Up/Down Command Selection 1
Sets the input method for the Up/Down command.
0: Keypad, 1: Digital Input, 2: Memobus/Modbus Communications, 3: Option PCB
b1-03
Stopping Method Selection
Sets the method to stop the motor after removing an Up/Down command or entering a Stop command.
0: Ramp to Stop, 1: Coast to Stop, 4: Elevator Emergency Stop
C1-01
RUN
Acceleration Ramp 1
Sets the ramp to accelerate from zero to maximum output speed.
C1-02
RUN
Deceleration Ramp 1
Sets the ramp to decelerate from maximum output speed to zero.
C2-01
Jerk @ Start of Accel
Sets the jerk at the start of acceleration.
C2-02
Jerk @ End of Accel
Sets the jerk at the completion of acceleration.
C2-03
Jerk @ Start of Decel
Sets the jerk at the start of deceleration.
C2-04
Jerk @ End of Decel
Sets the jerk at the completion of deceleration.
C2-05
Jerk below Leveling Speed
Sets the jerk when the speed reference is lower than the leveling speed setting.
C5-01
RUN
ASR Proportional Gain 1
Sets the gain to adjust ASR response at high speed.
C5-02
RUN
ASR Integral Time 1
Sets the ASR integral time at high speed.
C5-03
RUN
ASR Proportional Gain 2
Sets the gain to adjust ASR response at low speed.
C5-04
RUN
ASR Integral Time 2
Sets the ASR integral time at low speed.
C5-13
RUN
ASR Proportional Gain 3
Set the gain to adjust ASR response at leveling speed. The setting is active for deceleration only.
C5-14
RUN
ASR Integral Time 3
Sets the ASR integral time at leveling speed. The setting is active for deceleration only.
C6-03
Carrier Frequency
Sets the carrier frequency.
d1-01 - d1-08
RUN
Reference 1 to 8
Sets the speed reference in the units from
o1-03 [Speed Display Unit Selection]
.
d1-18
Speed Reference Selection Mode
Sets the mode of speed reference selection by digital inputs.
0: Multi-speed Mode1 (d1-01 to 08), 1: High speed has priority, 2: Leveling speed has priority,
3: Multi-speed Mode2 (d1-02 to 08), 4: Smart Replacement
d1-19
RUN
Nominal Speed
Sets the nominal speed reference when an MFDI terminal set for
H1-xx = 50 [MFDI Function Selection = Nominal
Speed]
is active.