Thermo Scientific AQUAfast AQ3700 User Manual Download | Manualshive

Page: 67 / 264

background image

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

1.1 Methods

Notes:

1. Run samples and blanks with the same batch of vials. The blank is stable when stored in
  the dark and can be used for further measurements with vials of the same batch.
2. Do not place the hot vials in the sample chamber. Cool the vials to room temperature for
  final measurements.
3. Suspended solids in the vial lead to incorrect measurements. For this reason it is
  important to place the vials carefully in the sample chamber. The precipitate at the
  bottom of the sample should be not suspended.
4. Clean the outside of the vials with a towel. Finger prints or other marks will be removed.
5. Samples can be measured when the Chloride content does not exceed 1000 mg/l.
6. In exceptional cases, compounds contained in the water cannot be oxidized adequately,
  so results may be lower than reference methods.
7. For samples under 100 mg/l COD it is recommended to repeat the test with the tube
  test for COD LR.

«
...
65
66
67
68
69
...
»

Summary of Contents for AQUAfast AQ3700









































































































































































































































































Reviews:

No comments

Related manuals for AQUAfast AQ3700

Brand: Camille Bauer Pages: 12

Brand: Nady Audio Pages: 2

Brand: NARDA Pages: 64

Brand: Omano Pages: 14

Brand: Kawai Pages: 8

Brand: +GF+ Pages: 64

Brand: +GF+ Pages: 12

Brand: +GF+ Pages: 48

Brand: Teledyne Analytical Instruments Pages: 107

Brand: Schneeberger Pages: 35

Brand: bentrup Pages: 9

Brand: Mic Pages: 2

BUCKMASTERS 1500

Brand: Sig Sauer Pages: 2

Brand: Anritsu Pages: 29

Brand: VWR Pages: 44

Brand: Gallagher Pages: 20

LAQUAtwin-Na-11

Brand: horiba Pages: 5

Brand: Hanna Instruments Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands