Thermo Scientific AQUAfast AQ3700 User Manual Download

Page: 141 / 264

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

1.1 Methods

12.

Fill a second clean vial with 10 ml of the water

sample.

13. Add

one GLYCINE tablet

straight from the foil and

crush the tablet using a clean stirring rod.

14. Close the vial tightly with the cap and swirl several times

until the tablet is dissolved.

15.

Transfer the contents of the second vial into the

prepared vial.

16. Close the vial tightly with the cap and swirl several times

until the tablets are dissolved.

17. Place the vial in the sample chamber making sure that

the marks are aligned.

18. Press

TEST

key.

Wait for a

reaction period of 2 minutes

After the reaction period is finished the measurement

starts automatically.

The result is shown in the display in:

mg/l Ozone

mg/l total Chlorine

Notes:

See page 129.

Countdown
2:00

T1 accepted
prepare T2
press TEST

*,** mg/l O

*,** mg/l total Cl

Summary of Contents for AQUAfast AQ3700









































































































































































































































































Search results

Summary of Contents for AQUAfast AQ3700

Reviews:

Related manuals for AQUAfast AQ3700

Brands by name

Popular brands

Thermo Scientific AQUAfast AQ3700, User Manual

Search results

Summary of Contents for AQUAfast AQ3700

Reviews:

Related manuals for AQUAfast AQ3700

Brands by name

Popular brands