manualshive.com logo in svg

Thermo Scientific AQUAfast AQ3700, User Manual

The Thermo Scientific AQUAfast AQ3700, a cutting-edge device incorporating advanced technology, guarantees accurate and swift measurements. Enhance your experience by accessing the comprehensive and user-friendly User Manual, available for free download on our website. Maximize your product's potential with step-by-step instructions and detailed specifications.

Share
Download
background image

2

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

1.1 Methods

Suspended Solids

0 – 750 mg/l TSS

Sample preparation

Blend  approx.  500  ml  of  the  water  sample  in  a  blender  
at high speed for 2 minutes.

1.  Fill a clean vial (24 mm Ø) with 

10 ml of the  

deionized water, 

close tightly with the cap.

2.  Place the vial in the sample chamber making sure that 

the   marks are aligned.

3.  Press 

ZERO

 key.

4.  Remove the vial from the sample chamber and empty 

the vial completely.

5.  Stir the blended water sample. Immediately rinse the 

vial with the water sample and fill with 

10 ml water 

sample

.

6.  Place the vial in the sample chamber making sure that 

the   marks are aligned.

7.  Press

 TEST 

key.

      The  result  is  shown  in  the  display  in  mg/l  TSS  (Total 

Suspended Solids).

 prepare Zero
 press ZERO

 Zero accepted
 prepare Test
 press TEST

4

8

3

Summary of Contents for AQUAfast AQ3700









































































































































































































































































Reviews:

No comments

Related manuals for AQUAfast AQ3700

Hach Surface Scatter 7 sc Instruction Sheet preview
Surface Scatter 7 sc
Brand: Hach Pages: 6
Hach sensION+ DO6 Manual preview
sensION+ DO6
Brand: Hach Pages: 118
Hach sensION+ EC5 User Manual preview
sensION+ EC5
Brand: Hach Pages: 388
Hach Orbisphere 51 Series User Manual preview
Orbisphere 51 Series
Brand: Hach Pages: 118
Hach ORBISPHERE 3650 Atex User Manual preview
ORBISPHERE 3650 Atex
Brand: Hach Pages: 51
Hach sensION+ EC71 Manual preview
sensION+ EC71
Brand: Hach Pages: 72
Hach POLYMETRON 8362 User Manual preview
POLYMETRON 8362
Brand: Hach Pages: 78
HACH LANGE Pocket Colorimeter II Basic User Manual preview
Pocket Colorimeter II
Brand: HACH LANGE Pages: 146
Hach Sigma 950 Instrument Manual preview
Sigma 950
Brand: Hach Pages: 146
Hach 2200 PCX User Manual preview
2200 PCX
Brand: Hach Pages: 36
Hach PHOSPHAX indoor sc User Manual preview
PHOSPHAX indoor sc
Brand: Hach Pages: 104
Hach Lange ORBISPHERE 3100 Basic User Manual preview
Lange ORBISPHERE 3100
Brand: Hach Pages: 384
Hach 5500sc SiO2 Installation Manual preview
5500sc SiO2
Brand: Hach Pages: 172
Halcyon TRAVELER Owner'S Manual preview
TRAVELER
Brand: Halcyon Pages: 36
R&S FSMR3000 User Manual preview
FSMR3000
Brand: R&S Pages: 733
R&S ZNH User Manual preview
ZNH
Brand: R&S Pages: 369
Yamaha ARIUS YDP-S34 Midi Reference preview
ARIUS YDP-S34
Brand: Yamaha Pages: 14
Yamaha Disklavier Mark II XG Series Advanced Operation Manual preview
Disklavier Mark II XG Series
Brand: Yamaha Pages: 12

Brands by name

Popular brands

Load more brands