Thermo Scientific AQUAfast AQ3700 User Manual Download | Manualshive

Page: 111 / 264

background image

0

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

1.1 Methods

Notes:

1. The reagent reacts with all soluble iron and most insoluble forms of iron in the water
  sample.
2. Iron oxide requires prior digestion: use mild, vigorous or acid digestion (e.g. for
  digestion with acid see page 105).
3. Very strong alkaline or acidic water samples must be adjusted to a pH value between
  3 and 5 before analysis.
4. Accuracy is not affected by undissolved powder.
5. Water samples containing visible rust should be allowed to react for at least five minutes.

«
...
109
110
111
112
113
...
»

Summary of Contents for AQUAfast AQ3700









































































































































































































































































Reviews:

No comments

Related manuals for AQUAfast AQ3700

Brand: Kawai Pages: 2

Brand: 3M Pages: 2

Brand: 3M Pages: 16

Brand: E Instruments Pages: 2

Brand: Hardy Barth Pages: 27

Brand: National Instruments Pages: 15

ProcessMaster FEP630 series

Brand: ABB Pages: 92

Brand: National Instruments Pages: 15

Brand: Hanna Instruments Pages: 2

Brand: SKF Pages: 12

Brand: Hanna Instruments Pages: 2

American AL-1000

Brand: Badger Meter Pages: 16

Brand: Teledyne Pages: 81

Brand: Omega Pages: 4

Brand: Vanguard Instruments Company Pages: 111

Brand: Rubicson Pages: 4

Brand: SEAWARD Electronic Pages: 57

Brand: Feasa Pages: 145

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands