Thermo Scientific AQUAfast AQ3700 User Manual Download

Page: 72 / 264

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

1.1 Methods

Copper

with Tablet

0.05 – 5 mg/l Cu

The following selection is shown in the display:

for the differentiated determination of free, combined and
total Copper.

for the determination of free Copper.

for the determination of total Copper.

Select the desired determination with the arrow keys
[ ] and [ ]. Confirm with [ ] key.

Note:

1. If ??? is displayed at the diffentiated test result see page 242.

Copper
>>

diff

free

total

diff

free

total

Summary of Contents for AQUAfast AQ3700









































































































































































































































































Search results

Summary of Contents for AQUAfast AQ3700

Reviews:

Related manuals for AQUAfast AQ3700

Brands by name

Popular brands

Thermo Scientific AQUAfast AQ3700, User Manual

Search results

Summary of Contents for AQUAfast AQ3700

Reviews:

Related manuals for AQUAfast AQ3700

Brands by name

Popular brands