Thermo Scientific AQUAfast AQ3700 User Manual Download

Page: 233 / 264

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

Delete stored results

Press [MODE], [Shift] + [3][4] keys.

Confirm with [ ] key.

The display shows:

Press [Shift] + [0] key to retain the data sets
in memory.

After pressing key [Shift] + [1] the following
acknowledgment is displayed:

Press [ ] key to delete.

ATTENTION:
All stored test results are deleted

or cancel without deleting data by pressing [ESC] key.

Note:

All stored test results are deleted.

2.4.5 Calibration

Fluoride Calibration

Caution: See notes!

Press [MODE], [Shift] + [4][0] keys.

Confirm with [ ] key.

The display shows:

1. Fill a clean vial (24 mm Ø) with exactly

10 ml

of deionised water

, close tightly with the cap.

2. Place the vial in the sample chamber making sure that

the marks are aligned.

•

<Delete data>
Delete all data?
YES : 1 NO : 0

<Calibration>
170 Fluoride
Zero: deionized water
press ZERO

<Delete data>
Delete data

Do not delete: ESC

Mode

Summary of Contents for AQUAfast AQ3700









































































































































































































































































Search results

Summary of Contents for AQUAfast AQ3700

Reviews:

Related manuals for AQUAfast AQ3700

Brands by name

Popular brands

Thermo Scientific AQUAfast AQ3700, User Manual

Search results

Summary of Contents for AQUAfast AQ3700

Reviews:

Related manuals for AQUAfast AQ3700

Brands by name

Popular brands