background image

2

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

1.1 Methods

Acid demand to pH 4.3 

with Tablet

0.1 – 4 mmol/l

1.  Fill a clean vial (24 mm Ø) with 

10 ml of the water  

 

sample

, close tightly with the cap.

2.  Place the vial in the sample chamber making sure that 
 

the   marks are aligned.

3.  Press 

ZERO

 key.

4.  Remove the vial from the sample chamber.

5.  Add 

one  ALKA-M-METER  tablet

  straight  

 

from the foil to the water sample and crush the tablet  

 

using a clean stirring rod.

6.  Close the vial tightly with the cap and swirl several times  
 

until the tablet is dissolved.

7.  Place the vial in the sample chamber making sure that  
 

the   marks are aligned.

8.  Press 

TEST

 key.

 

The result is shown in the display as Acid demand to 

 

pH 4.3 in mmol/l.

 prepare Zero
 press ZERO

 Zero accepted
 prepare Test
 press TEST 

2

0

Summary of Contents for AQUAfast AQ3700









































































































































































































































































Reviews: