Thermo Scientific AQUAfast AQ3700 User Manual Download

Page: 262 / 264

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

Patrick Chiu

Place and Date of Issue:

Senior Quality Engineer,

Beverly, MA

Regulatory Compliance

July 10, 2009

3.7 Declaration of CE-Conformity

Name of Manufacturer:

Thermo Fisher Scientific, Inc.

166 Cummings Center

Beverly, MA 01915 USA

Hereby declares that the following product:

AQUAfast AQ3700 Colorimeter

Conforms to the following standards:

EMC

Emission:

EN 61326:1997 + A1:1998 + A2:2001 + A3:2003

Devices for class B

Immunity:

EN 61326:1997 + A1:1998 + A2:2001 + A3:2003

Requirements according to table A1, industrial environment

Applicable standards:

61000-4-3:1996 + A1:2002

This product conforms to the regulations of the directive 2004/108/EG of the European
Parliament and the Council of 2004, December the 15th.

Summary of Contents for AQUAfast AQ3700









































































































































































































































































Search results

Summary of Contents for AQUAfast AQ3700

Reviews:

Related manuals for AQUAfast AQ3700

Brands by name

Popular brands

Thermo Scientific AQUAfast AQ3700, User Manual

Search results

Summary of Contents for AQUAfast AQ3700

Reviews:

Related manuals for AQUAfast AQ3700

Brands by name

Popular brands