Thermo Scientific AQUAfast AQ3700 User Manual Download

Page: 230 / 264

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

Recall results of a selected time period

Press [MODE], [Shift] + [3][1] keys.

Confirm with [ ] key.

The display shows:

Enter year, month and day for the for the first day of the
required period, e.g.: 14 May 2006 =
[Shift] + [0][6][0][5][1][4]

Confirm with [ ] key.

The display shows:

Enter year, month and day for the last day of the required
period, e.g.: 19 May 2006 = [Shift] +[0][6][0][5][1][9]

Confirm with [ ] key.

The display shows:

• Press [ ] key and all stored results in the selected date

range are displayed.

• Press [F3] key to print the displayed result.

• Press [F2] key to print all selected results.

• End with [ESC].

Note:

It is possible to cancel the entry by [ESC].
If you want to recall only results of one day enter the same date twice to determine the
time period.

<Storage>
sorted: date
from yy-mm-dd
__-__-__

to yy-mm-dd
__-__-__

from 2006-05-14
to 2006-05-19
Start:

cancel: ESC

print: F3
print all: F2

Mode

Summary of Contents for AQUAfast AQ3700









































































































































































































































































Search results

Summary of Contents for AQUAfast AQ3700

Reviews:

Related manuals for AQUAfast AQ3700

Brands by name

Popular brands

Thermo Scientific AQUAfast AQ3700, User Manual

Search results

Summary of Contents for AQUAfast AQ3700

Reviews:

Related manuals for AQUAfast AQ3700

Brands by name

Popular brands