Thermo Scientific AQUAfast AQ3700 User Manual Download

Page: 172 / 264

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

1.1 Methods

pH value 6.5 – 8.4

with Liquid Reagent

1. Fill a clean vial (24 mm Ø) with

10 ml of the water

sample

, close tightly with the cap.

2. Place the vial in the sample chamber making sure that

the marks are aligned.

3. Press

ZERO

key.

4. Remove the vial from the sample chamber.

5. Fill the vial with drops of the same size by holding the

bottle vertically and squeeze slowly:

6 drops of PHENOL RED solution

6. Close the vial tightly with the cap and swirl several times

to mix the contents.

7. Place the vial in the sample chamber making sure that

the marks are aligned.

8. Press

TEST

key.

The result is shown in the display as pH-value.

prepare Zero
press ZERO

Zero accepted
prepare TEST
press Test

Summary of Contents for AQUAfast AQ3700









































































































































































































































































Search results

Summary of Contents for AQUAfast AQ3700

Reviews:

Related manuals for AQUAfast AQ3700

Brands by name

Popular brands

Thermo Scientific AQUAfast AQ3700, User Manual

Search results

Summary of Contents for AQUAfast AQ3700

Reviews:

Related manuals for AQUAfast AQ3700

Brands by name

Popular brands