manualshive.com logo in svg

Thermo Scientific AQUAfast AQ3700, User Manual

The Thermo Scientific AQUAfast AQ3700, a cutting-edge device incorporating advanced technology, guarantees accurate and swift measurements. Enhance your experience by accessing the comprehensive and user-friendly User Manual, available for free download on our website. Maximize your product's potential with step-by-step instructions and detailed specifications.

Share
Download
background image

3

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

1.1 Methods

13. Place the vial (the blank) in the sample chamber 

making sure that the   marks are aligned.

14. Press 

ZERO

 key.

 

Wait for a  

reaction period of 2 minutes

 (Note 7).

 

After the reaction period is finished the measurement 
starts automatically.

15. Remove the vial from the sample chamber.

16. Place the vial (the sample) in the sample chamber 

making sure that the   marks are aligned.

14. Press 

TEST

 key.

   

 

 

         The result is shown in the display as mg/L PO

4

 

3-

. 

To calculate the actual phosphonate concentration multiply the reading with the  
corresponding dilution factor from table 1.

To calculate the active phosphonate concentration multiply the actual phosphonate  
concentration using the appropriate factor from table 2.

Notes:

1. Rinse all glassware with 1:1 Hydrochloric acid first and then reinse with deionized water.
2. During UV digestion Phosphonates are convertd to Ortho-Phosphates.  
  This step is normally completed in 10 minutes. High organic loaded samples or a weak 
  lamp can cause incomplet phosphate conversion.
3. UV lamp must be purchased separately.
4. While the UV lamp is on UV safety goggles must be worn.
5. For handling of the UV lamp see manufacturer's manual. 
  Do not touch the surface of the UV lamp. Fingerprints will etch the glass. 
  Wipe the UV lamp with a soft and clean tissue between measurements.
6. The reagent does not dissolve completely.
7. The given reaction time of 2 minutes refers to a water sample temperature of more 
  than 15 °C. At a sample temperature of lower than 15 °C a reaction time of 4 minutes  
  is required.

Tables:

see next page

 Zero accepted
 prepare Test
 press TEST 

 prepare Zero
 press ZERO

 Countdown
       2:00

Summary of Contents for AQUAfast AQ3700









































































































































































































































































Reviews:

No comments

Related manuals for AQUAfast AQ3700

Kane 400 Quick Reference Manual preview
400
Brand: Kane Pages: 4
PASCO PS-3215 Battery Replacement preview
PS-3215
Brand: PASCO Pages: 3
Yamaha Arius YDP-160 Midi Data Format preview
Arius YDP-160
Brand: Yamaha Pages: 6
Yamaha AW4416 Manual Supplement preview
AW4416
Brand: Yamaha Pages: 48
MICRO-EPSILON ODC 2600-40 Operating Instructions Manual preview
ODC 2600-40
Brand: MICRO-EPSILON Pages: 82
Kane KM940 Manual preview
KM940
Brand: Kane Pages: 35
Veris E61C20 Installation Manual preview
E61C20
Brand: Veris Pages: 3
OHAUS a-AB23EC Quick Start Manual preview
a-AB23EC
Brand: OHAUS Pages: 6
E+H Micropilot S FMR533 Manual preview
Micropilot S FMR533
Brand: E+H Pages: 12
National Instruments AT-AI-16XE-10 Programmer'S Manual preview
AT-AI-16XE-10
Brand: National Instruments Pages: 169
Parkside PZM 2 A1 Operation And Safety Notes preview
PZM 2 A1
Brand: Parkside Pages: 199
Zircon MultiScanner HD800 OneStep Instructions preview
MultiScanner HD800 OneStep
Brand: Zircon Pages: 2
HERON dipper-T Operating/Maintenance Instructions & Warranty preview
dipper-T
Brand: HERON Pages: 2
Harken RigTune Pro Manual preview
RigTune Pro
Brand: Harken Pages: 2
Huvitz CRK-8800 Service Manual preview
CRK-8800
Brand: Huvitz Pages: 58
TEA 800506 Instruction Manual preview
800506
Brand: TEA Pages: 10
iSTEK K100-TB Instruction Manual preview
K100-TB
Brand: iSTEK Pages: 15
Hanna Instruments HI 98191 Quick Reference Manual preview
HI 98191
Brand: Hanna Instruments Pages: 2

Brands by name

Popular brands

Load more brands