Thermo Scientific AQUAfast AQ3700 User Manual Download

Page: 228 / 264

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

Printing Parameter

Press [MODE], [Shift] + [2][9] keys.

Confirm with [ ] key.

The display shows:

Press [Shift] + [1] key to select ”Flow control”.

The display shows:

Press arrow key [ ] or [ ] to select the required Protocol.
(Xon/Xoff, no control)

Confirm with [ ] key.

Finish with [ESC] key.

Flow Control will be set to the selection displayed at “is“.

Press [Shift] + [2] key to select ”Baud rate”.

The display shows:

<printing parameter>
1: Flow control
2: Baud rate

cancel:

ESC

<Flow Control>
is: Xon/Xoff
select: [ ] [ ]
save:

cancel:

ESC

<Baud rate>
is: 19200
select: [ ] [ ]
save:

cancel:

ESC

Mode

Esc

Summary of Contents for AQUAfast AQ3700









































































































































































































































































Search results

Summary of Contents for AQUAfast AQ3700

Reviews:

Related manuals for AQUAfast AQ3700

Brands by name

Popular brands

Thermo Scientific AQUAfast AQ3700, User Manual

Search results

Summary of Contents for AQUAfast AQ3700

Reviews:

Related manuals for AQUAfast AQ3700

Brands by name

Popular brands