Thermo Scientific AQUAfast AQ3700 User Manual Download

Page: 251 / 264

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

The display shows:

Enter the pH-value in the range between 0 and 12 and
confirm with [ ] key.

The display shows the Langelier Saturation Index.

Press [ ] key to start new calculation.

Return to mode menu by pressing [ESC] key.

Operating error:

Values out of defined range:

The entered value is too high.

The entered value is too low.

Confirm display message with [ ] key and enter a value in
the defined range.

Selection of temperature unit

Entering the temperature value is possible in degree Celsius or degree Fahrenheit.
Therefore the following preselection is (once) required.

Press [MODE], [Shift] + [7][1] keys.

Confirm with [ ] key.

The display shows:

Press [Shift] + [1] key to select degree Celsius.

Press [Shift] + [2] key to select degree Fahrenheit.

The instrument goes back to mode menu automatically.

pH value
0<=pH<=12
+_ _ _ _

<Langelier>
Langelier
saturation index
0.00
Esc

CH<=1000 mg/l CaCO3!

CH>=50 mg/l CaCO3!

<temperature>
1: °C 2: °F

Examples:

Mode

Summary of Contents for AQUAfast AQ3700









































































































































































































































































Search results

Summary of Contents for AQUAfast AQ3700

Reviews:

Related manuals for AQUAfast AQ3700

Brands by name

Popular brands

Thermo Scientific AQUAfast AQ3700, User Manual

Search results

Summary of Contents for AQUAfast AQ3700

Reviews:

Related manuals for AQUAfast AQ3700

Brands by name

Popular brands