Thermo Scientific AQUAfast AQ3700 User Manual Download | Manualshive

Page: 239 / 264

background image

237

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

2.4.6 Lab function

Reduced operator guidance => “Profi-Mode“

This function may be used for routine analyses with many samples of one method.
The following information is always stored in the methods:

a)  Method
b)  Range
c)  Date and time
d)  Differentiation of results
e)  Detailed operator instruction
f)  Compliance with reaction periods

If the Profi-Mode is active, the meter provides only a minimum of operator instructions.
The criteria specified above in d, e, f are no longer included.

Press [MODE], [Shift] + [5][0] keys in succession.

Confirm with [ ] key.

The display shows:

Press [Shift] + [0] key to switch the Profi-Mode off.

Press [Shift] + [1] key to switch the Profi-Mode on.

The display shows:

Confirm with [ ] key.

Note:

Storage of test results is possible. When results are stored the display also shows
“Profi-Mode” .
The selected settings are kept by the meter even whein it is switched off. To change meter
setting a new setting is required.

•

•

<Profi-Mode>
ON : 1 OFF : 0

0

Mode

0

5

1

switched off

or

switched on

«
...
237
238
239
240
241
...
»

Summary of Contents for AQUAfast AQ3700









































































































































































































































































Reviews:

No comments

Related manuals for AQUAfast AQ3700

Brand: Omer Pages: 2

Brand: Bartington Pages: 15

Brand: Bartec Pages: 216

Brand: YOKOGAWA Pages: 2

IEM-100 Beltpack

Brand: DAPAudio Pages: 19

Brand: RADWAG Pages: 12

Pasport PS-2138

Brand: Pasco Scientific Pages: 26

Brand: ASCEL Electronic Pages: 64

Comark Diligence 600

Brand: Fluke Pages: 61

WD-35606-00, WD-35606-05

Brand: Oakton Pages: 10

Brand: Fuji Electric Pages: 85

Brand: FM Marin Pages: 8

Thermo Scientific iCE 3000 Series

Brand: ThermoFisher Scientific Pages: 42

Micro Alti Vario Plus

Brand: Fairhaven Pages: 20

Brand: Integra Pages: 32

Brand: Agilent Technologies Pages: 20

KLIMA GUARD 30.5010

Brand: TFA Pages: 22

Celviano AP-650M

Brand: Casio Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands