Thermo Scientific AQUAfast AQ3700 User Manual Download | Manualshive

Page: 222 / 264

background image

220

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

Countdown (Ensuring reaction periods)

Some methods require a reaction period. This reaction period is incorporated in the method
as standard with the countdown function.
It is possible to switch the countdown off for all methods:

Press [MODE], [Shift] + [1][3] keys.

Confirm with [ ] key.

The display shows:

• Press [Shift] + [0] key to switch the countdown off.

• Press [Shift] + [1] key to switch the countdown on.

Confirm with [ ] key.

Notes:

1. It is possible to interrupt the working countdown by pressing the [ ] key (application e.g.
serial analysis).

  The “user countdown” is also available if the countdown is switched off.
2. If the countdown function is switched off, the operator is responsible for ensuring the
  necessary reaction period.

Non-compliance with reaction periods leads to incorrect test results.

<Countdown>
ON: 1

OFF: 0

0

Mode

3

1

1

«
...
220
221
222
223
224
...
»

Summary of Contents for AQUAfast AQ3700









































































































































































































































































Reviews:

No comments

Related manuals for AQUAfast AQ3700

Brand: Van Walt Pages: 2

BML SL1-ALZ-ZZ Series

Brand: Balluff Pages: 26

IEM-100 Beltpack

Brand: DAPAudio Pages: 19

Brand: Hammond Pages: 130

Brand: National Instruments Pages: 15

Brand: National Instruments Pages: 85

Brand: National Instruments Pages: 12

Brand: National Instruments Pages: 18

Brand: National Instruments Pages: 12

Brand: Artesia Pages: 36

Brand: Orange Electronic Pages: 21

Brand: Olimpus Pages: 12

Litemaster Pro L-478DR

Brand: Sekonic Pages: 16

Brand: PCE Instruments Pages: 6

Brand: TAC Pages: 28

Brand: Hammond Pages: 36

Brand: SIMET Pages: 2

Brand: red lion Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands