manualshive.com logo in svg

Thermo Scientific AQUAfast AQ3700, User Manual

The Thermo Scientific AQUAfast AQ3700, a cutting-edge device incorporating advanced technology, guarantees accurate and swift measurements. Enhance your experience by accessing the comprehensive and user-friendly User Manual, available for free download on our website. Maximize your product's potential with step-by-step instructions and detailed specifications.

Share
Download
background image

7

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

1.1 Methods

12.  Close the vial tightly with the cap and swirl several times  
 

until the tablets are dissolved.

13.  Place the vial in the sample chamber making sure that  
 

the   marks are aligned.

14.  Press 

TEST

 key. 

 

Wait for a 

reaction period of 10 minutes

.

 

After the reaction period is finished the measurement  

 

starts automatically.

 

The result is shown in the display in mg/l Urea.

Notes:

1. The sample temperature should be between 20°C and 30°C.
2. Carry out the test at the latest one hour after sample taking.
3. The tablets must be added in the correct sequence.
4. Do not store reagent 1 below 10°C; granulation is possible. 
 

Store reagent 2 (Urease) in the refrigerator at a temperature of 4°C to 8°C.

5. The AMMONIA No. 1 tablet will only dissolve completely after the AMMONIA No. 2 
  tablet has been added.
6. Ammonia and chloramines are also measured during urea measurement.
7. Before analysing seawater samples, a measuring spoon of Ammonia Conditioning 
  Powder must be added to the sample and swirled to dissolve before AMMONIA No. 1 
  tablet is added.
8. Fill the vial with drops of the same size by holding the bottle vertically and squeeze  
  slowly.
9. 

Due to the reagent’s storage and shipping requirements, this reagent is not 

  available in many locations.

 Countdown
      10:00

 Zero accepted
 prepare Test
 press TEST

Summary of Contents for AQUAfast AQ3700









































































































































































































































































Reviews:

No comments

Related manuals for AQUAfast AQ3700

ABB Endura AZ20 series Instruction preview
Endura AZ20 series
Brand: ABB Pages: 8
Gardner Bender PM3000 Operating Instructions preview
PM3000
Brand: Gardner Bender Pages: 4
GAPS Clack WS1 Installation, Operation And Maintenance Manual preview
Clack WS1
Brand: GAPS Pages: 36
yellow jacket 68940 Operation Manual preview
68940
Brand: yellow jacket Pages: 26
IEI Technology IW04-MB14-N User Manual preview
IW04-MB14-N
Brand: IEI Technology Pages: 85
Navman A300 Sport.Tool Specification preview
A300 Sport.Tool
Brand: Navman Pages: 1
Keithley 610C Instruction Manual preview
610C
Brand: Keithley Pages: 44
Keithley 2651A User Manual preview
2651A
Brand: Keithley Pages: 76
Keithley 4200-SCS Startup Manual preview
4200-SCS
Brand: Keithley Pages: 12
Keithley 194 Instruction Manual preview
194
Brand: Keithley Pages: 281
Yamaha AW4416 Manual Supplement preview
AW4416
Brand: Yamaha Pages: 48
GF Signet FlowtraMag 2580 Series Operating Instructions Manual preview
Signet FlowtraMag 2580 Series
Brand: GF Pages: 20
Ocea Soft Cobalt 2 Installation Manual preview
Cobalt 2
Brand: Ocea Soft Pages: 19
Xsensor CLMI X-232 Operation Manual preview
CLMI X-232
Brand: Xsensor Pages: 13
RAM ODM808 User Manual preview
ODM808
Brand: RAM Pages: 43
ScienTECH Vector S310 Setup And Operating Procedures preview
Vector S310
Brand: ScienTECH Pages: 43
Barco D320LITE Installation Manuallines preview
D320LITE
Brand: Barco Pages: 33
J-TECH Solar Auxiliary Power Unit Operator'S Manual preview
Solar Auxiliary Power Unit
Brand: J-TECH Pages: 6

Brands by name

Popular brands

Load more brands