Thermo Scientific AQUAfast AQ3700 User Manual Download

Page: 249 / 264

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

Initialise User Method System (Polynomials & Concentration)

Power loss will cause incoherent data. The user method system must be initialised with this
mode function to set it to a predefined state.

ATTENTION:

All stored user methods (polynomial & concentration) are deleted with initialisation.

Press [MODE], [Shift] + [6][9] keys.

Confirm with [ ] key.

The display shows:

Confirm with [ ] key.

The query is displayed:

• Press [Shift] + [1] key to start initialisation.

• Press [Shift] + [0] key to to cancel without initialisation.

The instrument goes back to mode menu automatically.

<User m. init>
Start:

Initialising?
YES: 1, NO: 0

Mode

Summary of Contents for AQUAfast AQ3700









































































































































































































































































Search results

Summary of Contents for AQUAfast AQ3700

Reviews:

Related manuals for AQUAfast AQ3700

Brands by name

Popular brands

Thermo Scientific AQUAfast AQ3700, User Manual

Search results

Summary of Contents for AQUAfast AQ3700

Reviews:

Related manuals for AQUAfast AQ3700

Brands by name

Popular brands